With the arrival of our life of personal computers, it became relevant to make a computer desk corner with their own hands. Recently, angular computer tables are gaining increasing popularity. Made a computer table with your own hands, you can not only get furniture with an individual design, but also to save your budget significantly.
The homemade corner table will save place in the room and your budget.
Of course, you can buy a table in the store, but there are people who prefer to do everything with their own hands.
Where to start the manufacture of a table
Determine with dimensions
You can look at the location scheme on the table.
Before making an angular computer desk, you need to decide on the table form, its size, design, and possibly with some additional features. It is very important to clearly imagine its appearance, the materials used in the creation of the table will depend on it.
All that may be needed during the work should be prepared in advance.
Now it is necessary to make a project manufacturing a computer table. With it, it is necessary to consider some parameters:
- table features, it is important to provide such trifles as the number of boxes, as well as the need for a retractable shelf under the keyboard and other shelves under the office equipment;
- The height of the table, and it is very important for whom this table is manufactured, if it is intended for an adult, then a standard height is needed, if for a child, then it is necessary to choose the right height, focusing on the growth of the child, do not forget about the size of the swivel chair ;
- When planning additional shelves, you need to consider the size of the office equipment and make the shelves strictly under them;
- The size of the table must correspond to the room in which it will be, taking into account the furniture already located here.
Article on the topic: Warm resistance: how to check the thermostat and sensor
Before starting work, you need to make a sketch of the table with all sizes.
You can simply think about the storage of CDs, for this you need to measure the width of the pre-purchased plastic liner for disks. Now you need to perform a drawing in which all the necessary items are noted with an exact indication of all sizes. It is necessary in order to subsequently the most rational use the material. In the drawing, you must specify the number and type of fastening elements.
For the manufacture of a computer table with their own hands the following tools will be needed:
- line;
- striker;
- Ready plastic liner for disks;
- Lobzik;
- Screwdriver Set;
- Circular Saw;
- Drill and drill set.
From materials for the computer table, you will need:
List of materials for the manufacture of computer table.
- Pine boards required to enhance the product, the optimal thickness will be 25 mm boards;
- For shelves, boxes and side walls, it is better to take the MDF plate in the amount of quantity required;
- Screws for fasteners, about 130 pcs.;
- guides for shelves and boxes, their number will depend on the amount of data of the elements;
- plastic ties for angles;
- Faceted edge and grinding sliced for processing edges of boxes and shelves;
- Varnish or primer for final processing.
Make a computer table with your own hands is easy, but you need to be very attentive when stating dimensions in the drawings and when pruning individual elements from a large canvase.
Table assembly with drawers
After all the necessary items are cut, you can start assembling a computer table. You need to start the assembly with side elements. At the same stage, we produce a fastening of the guides under the retractable shelf and under the boxes. It is necessary to do it very accurately to avoid skewing boxes with further use. Then all the side walls are connected using the wrenches. In order to make the mount more durable, you can add PVA glue into the hole. Next, all walls are fixed using self-tapping screws.
Article on the topic: Curtains for the kitchen - an interior raisin
The edges that are visible are treated with the edge ribbon, such a tape is attached using a conventional hot iron, it is possible to try it through a thin cloth or ordinary paper.
Tools for the manufacture of a table: drill, jigsaw, screwdriver, screwdriver, passage.
A computer table can be installed depending on the pre-selected design. You can buy special metal round legs with a plastic base to avoid scratches on the floor, or at the initial stage, when designing, to provide the main focus on the side stands mounted on the above metal legs or simply on additional planks made from similar side stacks of the material.
After all the edges of the computer table are processed, you need to secure the worktop. As a rule, it is simply fixed on the wanks, after adding PVA glue into the holes. Holes for them are prepared in advance, having previously turned over the countertop using a drill. It is best to use the limiter in this case, since the depth of drilling is small and possible by negligence damage the front side of the table top.
Now we install in the guide board, intended for the keyboard, and insert the boxes. Check, whether everything works.
In the event that, according to your project, the monitor will not be installed on the worktop, but on a separate shelf, it is best to mount on a special metal stand, firstly, it is very stylish, secondly, reliably.
Space under the system unit
If you are going to use a personal computer behind this computer desk, not a laptop, you must provide a place under the system unit. It is best for these purposes a special stand. It is easy to make it, but the convenience of it will be mass. You do not have to climb your table with superfluous elements, while the system will be very mobile, it will not be tight binding it to the table. It is necessary for a base carved by the size of the system unit, as well as two side planks. To base, you can attach beautiful metal legs with a plastic base or install wheels instead.
Article on the topic: Electrical equipment for earthworks: purpose, choice, price
The manufacture of the table with your own hands is not too complicated and very exciting occupation. But it is necessary to approach him. The main thing is to provide at the initial stage all the little things, and also very accurately cut out individual elements. And then the table made with their own hands will exceed all your expectations.