From the vine, the people of ancient times are wearing a vine, only first saw from a grape vines, because such a name went - weaving baskets from the vine for beginners, although it is possible to use rods and other plants (raspberries, blackberries, currants). Then a person found a more flexible and durable plant - IVA. IV Broats are flexible and do not break as a grape vine, so there are large items from it and large objects, furniture (sofas, tables, shelves, shelves, armchairs), as well as smaller products, boxes, baskets, bread, dishes, vases, figurines , Frames for photos and much more, for which only fantasy is enough.
Many saw wicker products and some of them wanted to also get such a job in their own use. Therefore, the question often arises: "How to weave baskets from a vine with their own hands?". It is not difficult to weave that it is not difficult at all, only you need to stockday, patience and material for weaving.
Photoering on weaving
Preparation
For beginners in weaving from the vine, it will be more useful to prepare material itself, i.e. It is necessary to cut the annual rods in large quantities and with a margin, because the beginners of the rods in their work break more often. It is necessary to cut into thin bars with a sharp knife or a secateur, leaving another 3-4 kidneys on the branch so that the branch could continue to grow.
Before cut off a large number of vines from a certain bush, it is necessary to check flexibility on the first cut branch, i.e. It is necessary to bend it from the thick end in half, if not cracked, it means that it is suitable and can be cut further.
In order for the vine in the finished product to change the color, it should be soaked, preferably in running water (up to 1 month), disappear in hot water (1-2 hours) or reveal in boiling water (up to 20 minutes), clean from the bark, And then dry on a flat surface so that the color was uniform, without spots. Before the work itself, the vine should be shorted in water or wrapped in a wet rag and package to again give it flexibility so necessary during weaving.
Article on the topic: How to make a paper flower with your own hands: Instruction with photos and videos
Material and tools
Required for basket Material: 8 branches for the bottom cross, 7 mm in diameter and a length of 20-25 cm, for the stiffness of the walls - 15 rods with a length of 25-30 cm, and in diameter 5-7 mm, for braid - 20-30 pieces of vines thick in diameter no more 4-5 mm, and up to 1 meter long.Tools that will be needed while working: Knife, round-rolls, pliers, booths, shile different diameters, incl. And a thick curved awl (Kochess), load for holding work on site and tightening gum or rope.
Breaking DNA
Weaving basket begins with the Donets. It is necessary to take 8 thick rods in length approximately, in 4 of them to make a cut, i.e. It is necessary to split in the middle with a knife or shill to then insert 4 more rods, so it turns out the crusades of the bottom.
The braid braid begins with the "Rope" technique, the subtle ends of two rods are hiding in the crack of the cross, then the rods are separated and one goes over the axes of the cross, the other under the axes, then they are changing in places and so pass one or two rows in a circle.
Then the axis of the crosses are divided by two and sweeping further.
Then it is necessary to make an odd number of crosses, because It is necessary for a simple weaving, one of the rods are cut by the side. The rods are further moved and the corners between them are made the same so that the bottom it turns out round and the weaving was uniform.
So the weaving continues until the entire length of the rays will not be worn, the extra ends are cut off.
Basket walls
The next step will be the attachment of 15 side racks in weaving Punchka.
It is necessary to bend these racks 90 degrees, set to a vertical position and tie together the upper ends of the racks with rubber band or rope.
The border between the Don and the walls of the basket is further tired by three rods. It is necessary to take three pieces of vines and insert into the bottom to be subtle ends near each of the three consecutive racks.
Article on the topic: Openwork Pullover Crochet
The extreme left twist goes around two racks to the right, it comes to the third rack in the inside and leaves the outside near the fourth rack. In the same sequence, 2 other rods of the vine are brazed. It is so woven by several rows (2-3 pcs.) Movement (the border of the transition of the bottom to the walls of the basket) to form a form.
Wall weaving occurs in the usual weaving method, i.e. One rod behind the counter, the other - in front of the rack.
Next, you can remove the holding gum and weave as many rows of the basket walls, as far as the height of the basket is. Racks are cut off, and the fluttering rods are hiding in weaving.
Pen basket
It is necessary to take a thick rod with the necessary length and bend it such a form, which a handle should look in the finished form, the ends to sharpen and insert the walls on both sides.
Inserted next to a thick rod 6 thin rods with a thickness of 2-3 mm, the handle shall be fluttered, if necessary, tightly tape.
Also, on the other hand, 6 rods are inserted and they are trembling in the other side.
The ends of the rod are hiding in the weaving of the walls.
The basket is ready, only it is necessary to wait a little time until the rods are dried to the end.
Video on the topic
Video tutorials on the topic Weaving baskets from a vine for beginners.