After mounting the interior doors, the structural work may be discovered. The wines can lie on both the establishing company and the manufacturer or the owner itself. How to adjust interroom doors, if they are poorly closed? You can go in two ways: Call the owned brigade of workers or take reinstalling on yourself.
Interior doors
Defective door leather
In the event that the cause of bad closure of the interior door is the wrong dimensions of its web, is responsible for this the manufacturing company. The customer has the right to contact this organization and demand to compensate damage or replace interroom doors to new ones. In this case, it will have to carry out the installation process again. To avoid such a long, time-consuming and costly process, you can try to dismantle or adjust yourself.
When marriage, interior doors may not close due to:
- Dissolio of the door canvase;
- irregular dimensions (length, height) of the material;
- defective loops.
Installation of door loops
The easiest way to cope with the problem of loops. To solve, it is necessary to remove the door from the bottom of the fastener, leaving only the upper one that is attached to the canvas. If the case is in Rust, getting into the capsule of dirt or construction garbage, quite carefully clean the fasteners. When the loops constantly creak, do not move poorly when trying to close - it's a bad lubricant.
This option is solved without removing the interior door, simply pouring the oil to the engine elements. When the loops are relatively planned alone on the other, it is linked to the leaf, and then it is properly put on the lower part of the fastener, until two halves do not fully close.
Dimensional incomplete is the most difficult in processing. With it, there is not enough grinding circle, skins. It will take either a serious change in the edges of the design, or the terminal of the platbands. If it allows the doorway, they need to be expanded until a suitable gap is obtained.
Article on the topic: How to close the doorway with plasterboard - installation scheme
With weak disorders of the geometry of interroom doors, it is enough to use the plane and remove excess material from the door web. If the model was expensive and removing the upper layer will not be able to hide the overlay of its own paint and grinding, then in aesthetic purposes it is better to replace the door to a new one. Only unpainted, in the extreme case treated with a transparent wooden lacquer, is treated with branches and similar tools.
Problems in installing components
Often the correct closure of interior doors interfere with the twisted platbands, too high threshold or overall seals. After checking the presence of each of the problems, the master or owner should go to an adequate solution to the violation.
Repair door knob
The first case is the presence of too high threshold. Aluminum or rubber pad in the area of the bottom of the interior door can be located above the level of the lower door border and prevent its passage in the doorway. The threshold is dismantled and due to the cheapness of such a finish is simply replaced with a new, less dimensional. This question is easy to fix.
The second probable cause is a problem - skewing of platbands or the doorway itself. If one of the fasteners moved, for example, a nail, follows with the help of a hammer to drive it back into the wall and platband. If there is too much the size of the platbands, they are completely dismantled to correct the situation. In fact, you have to make reinstalling the product.
Sealers must be located clearly according to plan. If a deviation from it is noted and the problem closure of the interior design is observed, the position of the seals must be adjusted.
Problems when installing shut-off structures
Locks, cheeks and other products intended for the installation of personal space can greatly interfere with the door of the door with the wrong fastener algorithm. Due to the inattentive work of the master, part of the metal door junk can overlap the doorway. The tongue of the handle responsible for holding the door in the realmost position may be inverted and stored in the door leaf, while the special hole will be higher or lower. After diagnosing the problem and its clear definition, what to do, it is necessary to reinstall the defective design. Installation can take from 30 minutes to a pair of hours.
Article on the topic: We choose swab trees for cottages and gardens (40 photos)
Door structures
Turning handles are cut from the product using a screwdriver to adjust them. By revealing the restraining side screws, the locking device can be pushed with a sharp part of the screwdriver. It will be necessary to separately pull the handle and the plane around it, - through the front panel, and separately disassemble the lateral part of the mechanism, that is, the housing and recessed the tongue. In the case when the locks are then closed correctly, the installation was successful.
If the mechanical product is working and did not allow the interior partition to work correctly only due to defects that the installation brought, it is updated, correctly. If the case is in the marriage of the device itself, a new one is bought. The owners are available budget options from several hundred rubles that would not be.
Solving problems arising due to the owner's fault
What other doors do not close? Sometimes the owner of the apartment and interior doors installed in it can create a problem situation. By inattention or negligence, he may admit the following.
Blowing material. Products made of natural wood are strongly deformed and poorly closed under the influence of high humidity. If the owner by negligence did wet cleaning of the untreated door, constantly opened the windows during the rain, turned on the air humidifier, directing it on the doorway, then the swelling occurred by its fault. Over time, the material gets used to the environment, and moisture no longer affects it. Therefore, the problem may occur only in the first weeks after installation. It is worth talking about marriage when, after a month, interior doors did not become less.
Installation of interroom doors
Installing an inappropriate floor covering. Outdoor carpets or linoleum can be bad, frighten and trite to fall into the doorway, blocking it and the movement of the product from above.
The most banal error is to install wires over or below the door. Wiring (for example, a cable for an Internet connection) must be installed in such a way that it does not interfere. You need to monitor whether interior doors are closed correctly after correction.
Usually, the wiring is carried out either by plinth in special recesses, or even is carried out through the wall at acute necessity. You can overpow the cable, simply moving the mount to another place where the wires have become invisible, and rebuilding. To understand the correct location, you can use the photo.
Article on the topic: Floor screed mix: What is the best and proportion for fill
To compensate for water swelling, only the time and limitation of humidity will suit in the first period of using the product. And so that the floor covering is not fluttered and not falling into the lumen, it should be either moved (carpet), or straighten and seals to nourish the threshold of steel or aluminum and plinths (linoleum). The installation will take a few minutes.
After all the corrections, the owner will notice that now everything works correctly and interior doors are well closed.