Garland, which most often adorn the New Year tree can be used as a component component for the manufacture of the lighting device. The lamp from the garland is done simply.
For the manufacture of the lamp will require a garland, a plastic lampshade and a stand.
At the same time, the lighting in the room will be soft. Such a lamp can be used as a night light. The designs of such homemade luminaires can be diverse depending on fantasy and source materials.
Luminaires from disks and garlands: manufacture
The following materials will be required:
- CD or DVDs, which are both sides without pattern;
- Garland for 15-20 light bulbs;
- Glue and gun for applying it.
Starting the assembly of such a lighting device should be made from the manufacture of a geometric shape, for example, a cube or volumetric pentagon, which will be the basis. To do this, glue is applied to the disk and apply the other immediately. Consistently glue discs until the desired figure is obtained. But, in order to be more convenient to place inside the cube, one of its sides should be not blocked.
To attach discs, a glue gun or wire will be required.
After all the discs are glued, inside placed the garland. It is placed in such a way that the plug and the control box are in the window, which is formed by the articulation. Several light bulbs are removed into the holes. The number of placed inside the windows can be from 3 to 5, depending on the size of the light bulb. Glowing elements must completely fill the hole, thereby the desired effect will be created. The remaining part of the garland, which did not fit into the holes, are located inside the cube evenly. You should leave a few more light bulbs in order to turn them through the last strand, which is formed after gluing the last disk.
For the convenience of installing inside the holes, they can be copped with a scotch tape or an insulating ribbon. In addition, the resulting group additionally can be fixed with glue or sealant already in the process of their placement in the lamp discs.
Article on the topic: How to repair the bathroom in Khrushchev
After all the holes are filled with light bulbs, the last part of the lamp cube should be glued. In the last disc, light bulbs left for this purpose.
As a stand, you can use another disk. With the help of glue glue the cube, installing it on the edge. Such placement will allow you to steadily stand the lighting device in the future. At the same time, it should be considered that the socket and control box were placed at the bottom, but they were not glued.
After the design is installed on the stand and the glue will finally freeze, the lamp is ready for operation.
Plastic packaging and garland lamp
Power circuit of garlands in the lamp.
In order to make this model, the following materials and tools are needed:
- The foundation. As it can be used a plastic bottle of any size or a packing box of plastic diverse shape, for example, a housing from the pyramid-shaped candy.
- Garland, the number of light bulbs in which depends on the size and shape of the selected base.
- White paint. It is desirable that the paint be in the cylinder. This will evenly distribute it over the entire surface to the smooth layer.
- Soldering iron with a sharp tip (or electrical drill and drill with a diameter).
- Construction knife.
Before performing the slots, it is necessary to mark up. They can be placed symmetrically and 1 piece in the hole (or in the form of any drawing of several pieces inside). Based on the bottom, it is necessary to perform a rubber, through which the wire with a socket and control box will be passed.
If the material from which the base is made allows the holes using the soldering iron, while not damaging it, it is better to use it. In case of violation of the integrity of the structure, when exposed to a heated soldering iron, it is necessary to apply drill and drill to work. Holes are performed on the markup using the tool that is suitable for the selected base.
Article on the topic: Instruction How to hang the door to the loop do it yourself
If, as a result of the holes, sharp edges or part of the plastic remained outside either inside, then these residues must be neatly cut off using a building knife. It is necessary to perform it carefully and so as not to damage the rest of the foundation.
After the processing of the grooves is over, you can start painting. The base is required to paint several times so that uniform white color is formed over the entire surface.
After the paint dried, you can place light bulbs in the holes.
For convenience, work should be started on top. After all the lights are placed, and the wire with a power outlet and a control box are laid into the slot, the base should be closed with a lid. This will move the lamp on the room. The lamp is ready for operation.