Working with a manual saw, always need to have a support. This is not a process with a chainsaw, where everything is easier. From this directly depends on the safety of the operator. Such a table will be convenient for work not only a professional, but also the more lover, not to mention newcomers. Therefore, to equip your workshop with everything necessary every master.
Combining high maneuverability and greater performance, manual disk saw is an indispensable tool for even cutting various materials.
In order not to spend money, it is worth thinking about how to assemble the table for the manual disk saw with your own hands. He will be able to help out when you have to deal with big wood plates.
Some features and characteristics of the tool itself
To have an idea of the importance of an additional device (the table itself), it is necessary to represent the characteristics of the tool itself, so that the table is made not ababa as, but reliably. Not only the quality of work, but also the safety of the person himself depends on this.
Diagram of the device of the manual saw saw.
The disk saw is a device designed for the sewage of natural wood and its artificial analogues. Such a tool is convenient to work absolutely in any direction. In many ways, the safety of working with a saw depends on the accuracy of the guide devices and on how reliably the cutting body is limited.
In order for the sawing process to be convenient and physically not overloaded, it is very important that the tool is properly balanced. This moment can be checked when the device is turned off. Modern technologies provided disk saws by "brains", that is, electronics. Such control allows you to choose the speed of work, and when you start to give a smoother course. And in the case when the saw begins to experience the load, the system automatically adds power.
It should be borne in mind that the power of the saw engine is directly proportional to the diameter of the disk, since the torque parameter depends on this. Thus, it is possible to overcome the resistance of the sawing, which arises due to the fact that the lever of the resistance force of the material is lengthened. Therefore, the saw worked better, it is necessary with a relatively small diameter of the disk, to take the device with good power.
Types of disks for manual disk saw.
Operation of this technique implies the production of a large amount of sawdust. As a result, the floor acquires a sliding surface, and the air is saturated with dust, because of which it becomes difficult to breathe. Clothes are also dirty. To avoid these troubles, it is necessary that the saw has a nozzle for dusting. Usually it is located on the top of the guide and acts in such a way that all chips and sawdust flute to the side. As an alternative, you can use for this purpose and vacuum cleaner, the hose of which is connected to the nozzle.
To have the ability to move the cloth under the tilt (up to 45 °), it is necessary to weaken the clamps on the housing. For variation of the angle, the orientation takes on a special scale. In order to see this indicator for sure, it is necessary to make a trial cut. The slope will affect the depth of propil.
Article on the topic: how to clean up home furniture at home
How to work properly saw at an angle
Disc saw saw performance circuit.
The disk saw is a very dangerous tool. Therefore, each manufacturer equips its products with a fuse button, which is most often located on the side of the handle. Without her press, the saw will not work.
Since the cut is made by the bottom of the saw, it remains open, and only slightly covers the moving fence, while the upper is protected by a stationary casing. While working with the material, pressing the cloth, the fence is moving away from pressure, opening the disk itself. Releasing push, everything returns to its place. It is very important that the moving part worked without jail, otherwise work with such a device will be difficult.
Movable casing: features
Another fuses serve clamping flanges, which are located on both sides of the disk. In the case when the working material encloses, the flanges contribute to the slide of the clamps, so that the engine does not overheat.
It is very important that the handle itself has a comfortable shape, easily lying in his hand, not gliding in it. Only in this case the operator can and conveniently, and safely operate tool.
To make more or less deep feeds, it is only enough to raise or, on the contrary, omit the disk saw, focusing on the reference ski. You can focus using the scale or the billet. If it is necessary to cut the elements completely, the saw should look at 2-3 mm.
The diagram of the application of the disk saw.
Working with wood, there is such a feature as its tension between the fibers, which is released if the work is carried out along the fibers. This property of the material leads to the fact that it is very often for the disk, it is closed with a breakdown and then the canvas jamps. So that it was not, the saws are equipped with special knives behind the disk itself, which are located at a distance of 2-3 mm. For correct operation, the tip of the knife must be 0.3 cm higher than the lowest tooth of the saw.
A very important point is the choice of work material. It depends on which the disk will be used, because if it is an ordinary wood for a fence, then you can do the cheapest disc. But if the quality of the canvas is needed by the highest level, without any sowing, to minimize external defects and intervention of finishing works, it is worth choosing equipment with high-quality discs.
If any compounds should be cut from the material, then the canvas should have the highest quality. Well, if the saw disk has a Teflon coating, thus it reduces the moments of friction, it means that the mechanism itself will serve longer. In addition, if the device works at high speeds, it will not "burn out" a tree. There are options for discs when the teeth are covered with tungsten carbide. Such a coating allows you to extend the life of the saw, and the work itself is performed more cleanly. If necessary, you can install discs for cutting not only wood, but also metal, plastics or stone.
Work with disk saw
During the operation of the disk saw, its teeth moves upwards, therefore, the control itself must occur from above. In order to be at least the defects are visible on the workpiece, it is best to have wood facial surface down. It is very important that the workpiece is firmly fixed, the quality of work and the safety of the operator directly depends on this.
Ski of the disk saw has a small cut, which serves as a "sight."
Casting angles of disk saws.
Article on the topic: What better to make the floor in the room
Before you begin directly to the sulfice itself, it would be nice to make a couple of trial movements on an unnecessary tree so that it is possible to match the vizier and propyl.
Works can be carried out both by markup and using the guide line. Therefore, depending on individual skills, one or another apparatus is purchased.
It is very important that after each sawing saw closed its protective fence, and the disc itself came to a fixed state. Therefore, while the disk does not stop, there is a better saw on the table.
A very important point is also personal safety. First, before starting work, it would be nice to have safety glasses, gloves and even a respirator. The clothes itself should also be not from lightweight materials. And secondly, since the work is made with a tree, it should be eliminated near all the foci of open fire.
Table for disk saw poultry
For domestic workshops, a garage is very often used. Of course, if there is your private house, then under such a room you can allocate a whole separate room or some building located in the site.
Each man tries to adapt the workshop to herself, but this does not mean that it should not meet certain requirements.
Circular saw stood.
First of all, it is worth talking about the presence of furniture. Working with wood and metal involves the presence of absolutely different tools and technology. Even the professionals are drying when the device crashes out of hand. Therefore, in order to keep everything in integrity and safety, you need to have furniture in the workshop only the most necessary: table, a couple of chairs, stool, wardrobe and shelves.
Just about the table it is worth talking separately. Such a tool like a disk saw cannot work on weight, she needs a support, so with the help of a special fastening mechanism, many fix it straight to the table surface. As a result, it has to quickly look for a new replacement table, and all because the usual table is not suitable for performing this function.
And then there is an opportunity to solve this issue by assembling the table alone. The most convenient thing is that it will require minimal financial costs. All healthy material will consist of:
- wooden boards or bars;
- multilayer plywood;
- hammer;
- nails (nuts, screws);
- glue;
- building level;
- yardstick;
- chisels;
- hacksaws;
- electric drills;
- screwdriver.
Wood can always be taken from an unnecessary, broken old furniture. Thus, it can be saved on the base of the table and on its legs.
The main condition for such a design is the level of surface. After all, the disk saw requires great accuracy, and if such a table is not even or wandering, it can be sufficiently unsafe.
If there are skills in the construction sector, you can create a table for individual needs. But if you take for this question for the first time, it is best to create the design of the simplest view.
Article on the topic: Design, new products and selection of short curtains for the bedroom
Schema of the saw table.
After all the tools and materials are available, you can start working. All elements of the tree must be fastened with each other and reliably. For this, nails are used, as well as for reliability, you can use yourself with the help of bolts with nuts and screws.
The first thing is made the basis. This moment you need to pay special attention, as it is a support and guarantor of the safety of the operator. The most convenient option is a pair of wooden goats. For this, wooden bars are cut into separate parts, a height of 0.72-0.76 m. This is a fairly acceptable height for the working surface. But this parameter can be changed, depending on the growth of the employee. In addition, with the help of wooden flooring, you can adjust the height of the table to itself, making it higher or lower.
Next, elements of the supports are bonded between themselves through nails (screws or screws). After that, we are engaged in installing wooden crossing on the upper part of the goats. The evenness of such fixtures must be controlled using a construction level. For your own convenience, it will be better if such a table is collapsible so that if necessary, it could be disassembled and removed somewhere on storage.
Multilayer plywood will serve as the working surface of the table. It is best if such a material is not thinner than 2 cm, and its surface must be perfectly smooth, without any irregularities or bends. The optimal size of the working surface is 65x90 cm. Two bars are fixed along the length of the table, and four - in width. All mounting occurs with the help of nails (screws, screws).
Since the table is designed for a disk saw, it is necessary to take care of the hole for it. It is desirable that it is in the center of the table. The standard width size of such a slot will be 2 cm, taking into account the protective covers. The length exceeding will vary in the range of 25-30 mm, depending on the diameter of the saw disk. From the bottom side of the surface with the help of clamps, electric saw was attached. In this case, it is recommended to use the screws with countersunk heads. At this stage it is very important that the saw saw in the on-board has a parallel rotation of the slot.
Conclusion and summing up
Upon completion of the assembly of the table, it is necessary to polish all sowing on the tree. First, it will give a complete type of product, and secondly, there will be no risk to catch clothes at the table or simply drive the opponel to your finger.
Of course, if you can, then such a table can be built of metal plates. He will last much longer.
A manual disk saw a very convenient tool in home everyday, but in a set with the table, its functional range will significantly expand. And after all, the main thing is that it is worth noting, in the presence of a table under the disk saw during the work on it, the costs of physical strength are much smaller, it means that the work can be performed more and not too tired.