After the end of the finishing work along the floor joint with the walls, the MDF plinth is installed - not only in order to hide the seams, but also in order to improve the heat and sound insulation quality of the floor covering. MDF universal, it can be used with floor coatings from various materials. Speecually looks like a white plinth made of it - perhaps this is the most popular model.
Scope of application
Products from MDF have a long service life. Due to water-repellent properties, they can be mounted in residential and economic premises. Laminated material has been particularly well established: except for an attractive appearance, it is highly resistant to environmental impacts. It perfectly transfers sharp temperature differences, interaction with active chemicals. Therefore, its installation is recommended even in public institutions, where the floor covering is subject to particularly strong wear.
Also, the plinth from the MDF is not toxic. It is made of compressed wood waste, which adds special binders. Facial and decorative layers are applied to the surface of the panels - durable paper treated with special impregnation, as well as melamine. These layers are designed to protect MDF from external influences, melamine, in particular, prevents absorbing moisture. All materials used for the production and painting of plinths are environmentally friendly.
If desired, the product can be painted in a white or different color. Separately produced baseboard floor MDF, intended for staining and having such a surface that provides good adhesion of paints and varnishes. Often white plunths are used to emphasize the contrast between the floor and the walls. Laminated material looks effect: it is used to finish receiving, conference rooms, workers' office.
Article on the topic: Curtains on velcro do it yourself: Step-by-step instructions (video and photos)
Consumer properties
In addition to increased strength and increased durability, the MDF products are inconspicuous to operating conditions. To preserve the attractive appearance of the plinth for a long time, the material surface follows from time to time to rub the semi-dry cloth. Employed contamination is purified by a soap solution.MDF products are contraindicated with strong mechanical loads. From strong blows on the surface of the material, cracks may appear and other damage.
Preparation for installation work
The installation of the plinth begins after the flooring is fully prepared. If the linoleum or tile is mounted in the room, it should be waited when the glue or solution is dried. White plinth - universal material, it is combined with all types of coatings, even with carpet.
The calculation of the plinth length is calculated. For this measure the perimeter of the room, and add to the resulting value of 3% about the supply. Most manufacturers release MDF plinth in the form of 260 mm longs, and to find out the required amount of its sections, the perimeter of the room should be divided into the length of the rail.
Mounting options
The usual and laminated plinth attach to the walls using special clips with hooks bent up. Installation of mounting elements is carried out at a distance of 50-60 cm from each other, the width of the hooks themselves is 10-15 cm. To connect the fastening elements with the wall of the 5x40 dowels. Clip samplers usually correspond to the size of the plinth. For example, if the plinth is high, it will not fit ordinary fasteners, and it is necessary to buy clips of non-standard sizes.
Instead of clips, guide rails can be used, some of them are equipped with special cable laying cells. Also, the plinth can be attached to the surface of the wall with glue: the mixture has no white color, but is transparent, and will not spoil the interior with proper handling.
Article on the topic: What color to choose a bedroom wallpaper: 6 practical advice
Occasionally, the installation of the plinth is performed using screws. This is not the best option, since screwing the fastening elements have to mask with a special composition. The masking material has a white shade, due to which its scope is limited.
Clip Mounting Technology
On the reverse side of the railtus racks have cells intended for attaching clips or guides. If you are planned to hold a cable, its installation is carried out simultaneously with the installation of plinth elements. It is neatly laid into the cells allotted for this cell or guides, and only when the stack is complete, fasten the white or color plinth.If you need to create angular joints, the plinth rails are cut. For this, it is used for a metal knife: it has small teeth, which, with friction, create a minimum load. Also, thanks to the use of hacksaw, the vibration created when sawing is reduced. As a result, cracks and chips appear on the surface of the material, and the laminated plinth retains an attractive appearance. If cracks appeared on the surface of the rail, it is impossible to get rid of them. Especially flaws will be noticeable on the surface of the material painted in white.
Application of plastic fittings
In the fields of the joint, the installation of plastic accessories is carried out, which masks the docking seams. Depending on the form and location of the installation, these details are divided into several varieties:
- Outdoor corner - Designed for mounting on protruding corners;
- Internal corner - installed in the joints of two perpendicular rails;
- compound - covers the seams that are formed in the fields of the joint of the rails on direct sections;
- plug - Mounted in places where the plinth is interrupted, for example, next to the doorways.
Typically, plastic fittings are painted in the color of the rivers, for example, in white, but models are presented on sale and under independent painting. Fasteners are performed with glue, which provides additional joint strength.
Article on the topic: Wire crafts for garden
Painting Reques
Staining is not subject to laminated plinth: this material is already covered with a layer of laminate, and does not need additional processing. Manufacturers produce a special MDF plinth under painting well absorbing paint mixes.
Before applying the paint to the surface of the rails, they must be prepared by treating the primer. The rose pile is removed by grinding. Next, the surface of the product is so ground twice, and the second time after applying the primer, grinding works are again carried out. After the third layer of primer dry, begged directly to painting the material.
Paint is chosen on the RAL scale. You can pick up any color, even white with shades. Staining is performed using a brush, the roller is rarely applied so that the paint does not hit the surface of the walls and the floor. Also, they can also be protected from random droplets using painting scotch.