The interior stools are the most important functional part of it. And if recently in the bedrooms and living rooms stools have become no longer as a common attribute, then in the kitchen without them can not do. And in those houses or apartments, where the premises are presented in antique style, there are practically stools in all rooms.
Drawing stool.
But, as a rule, over time, any, even the highest quality and reliable, the stool can come to a dissent state and demand repair. And then you need to immediately be accepted for work and not pull with this business. The earlier start it to repair, the easier it will be to go. And the less likely that someone falls from the broken herd.
Taberet repair in most cases does not require any special skills or skills. Even if all the chair fully needs to be updated, do it with your own hands is completely simple. You will need only stockpore and the necessary materials.
Consider the main options for the repair of individual parts of the tokevet alternately.
Repair of legs stuffing
To begin with, we will analyze how to repair the broken legs of the tobupere. There are several ways to be here, depending on what attachment they have. For the most part, legs can be mounted in two main ways: with a thread with bolts or with glue.Montage with glue
Stools cover repair scheme.
So, if the legs on the stool are kept on the glue and stumbled greatly, it is advisable to do so. First you need to carefully disconnect completely badly holding legs from the seat. Then, with the help of a sharp knife, free them from the remnants of the old glue. It is necessary to remove the glue and from the recesses in which the legs were included. It is convenient to do the chisel.
Article on the topic: How to make a barn at the cottage: and organize the storage of things (22 photos)
When the old glue is practically not left, you can clean these places using large sandpaper. After all, it is very important that the surface of the mounting places was as smooth and smooth. It provides the best clutch.
Now you only need to re-glue legs. Apply a sufficient amount (if there is a lot - it is not enough, excess can be removed) joinery or super glue into the notches for the legs. A little glue should be applied to the legs themselves. Then quickly need to stick the legs and press tightly. When it is done, it is necessary for about a day (depending on the specific type of glue) leave the stool in the inverted position so that the glue grabbing.
Thorough restoration of leg threads
The following type of fastening is on the thread. The greatest trouble is the fastening with a threaded stud. As a rule, it is screwed into the seat, and the leg is screwed into it in the excavation. Most often, the feet falling out of the seats together with the stud. In this case, repair is necessary.
Scheme of restoration of the thread of the legs.
Disconnect the frame from the seat into which the hairpin was screwed directly, and drill a hole slightly more. After that, make a new thread in this holes (preferably the same size), after which it takes a new stilet on this thread and screw it there. Exactly such a carving is renovated on the leg itself. Or as an option - just updated the old layer of thread.
But it happens that over time, the thread on the leg is still damaging, as a result of which the leg begins to crack and change in its size in width. Then you need to do so. Take the most ordinary canned jar and cut off the strip from its metal, the length of which will be such that it can be crushed around the leg plus about 2 cm for fixation. Strip width - about 1.5 cm. From one edge of the strip (which will be riding) It is advisable to make small cloves.
Article on the topic: The procedure for overhaul
Now such a "clamp" is put on the upper part of the leg, after which it is fixed with the help of an ordinary nut bolt. You can also twist the well-remaining part of the strip, if you succeed. But the cloves must be bandaged - this will ensure the maximum holding of the clamp on the leg.
Improving old thread and decoration
But it happens that the thread on the leg or on the heel is damaged only slightly, and it is a pity to completely redo it. As a rule, in such cases the stool is watched only slightly. In this case, you can promote legs and simply compact the threads.
Stool seat repair scheme.
It is easy to do with linen fiber or thread, which is simply wound on the thread with one layer. It is also quite acceptable to use FUM tape, which is often used in the plumbing.
When the legs are ready in the functional plan, you will only have to transform them decoratively. To do this, it is best to clean them from old paint or varnish, sand and paint again. After sufficient burrows, it will be possible to use this piece of furniture again.
How to repair the tobuck seat
But besides the legs, the repair may be required and the scene of the toaster. Typically, the seat is simply wears from time to time becomes ugly. And the exhaust lateral decoration is just behind, thereby it can easily arm. Therefore, it is also important to know how to cope with such a type of repair.
In the event that the seat is very old, you need to cut down and make a new one. At the same time, it is important to cut the sizes that you want to see. You also need to round the corners with the help of electric jigsaw and good seat to handle emery paper.
Further, depending on how you want to see the Tuberet's seat, it is necessary to treat it with varnish (paint) or can be caught a thin plywood or a special furniture film. Both options are good, so here you already have to determine clearly.
Article on the topic: how to install an overhead lock on a wooden door
Next, it remains to make the edge. Mount it is completely optional. If your stool is already beautiful, without it you can do well. But if you think that with the edge of the chair will look better, proceed to work. Immediately pouter with a special furniture edge in the desired quantity, the wrong part of which is covered with a thermoclayer, a sharp shoe knife, an electric iron.
First, the iron turns on and is displayed at least 150 degrees. At this time, you need to cut off the desired amount of the edge - about 5-10 cm more than you need for the salary. Next, it is convenient to work together. One person applies the edge and holds it, and the other drives into the heated iron. Thermocles are heated and fixes the edge to the seat.
It is important not to create even minimal gaps. And if they are - it is necessary to stroken everything until they disappear. And if the edge stuck unevenly, it's pretty easy to fix: just swing it again, disconnect and stir up. When everything is ready, cut the remnants of the edge with a shoe knife.
Repair of stools can be considered fully considered. Of all the above, it is easy to understand that this is a completely simple matter. Moreover, it is absolutely necessary to repair the stuff completely if only some specific parts were faced.