By installing new windows on the loggia, the question immediately appears, how to set off? You can hire a specialist to perform these works, but I don't really want to attract third-party people to a small volume, and the cost of completing the breakdowns is most often rather small. In principle, you can make such a job independently, because the alignment of slopes on the loggia is made by two methods: plaster or other finishing materials.
How to set off on loggia
The importance of decoration of slopes
After installing windows about the outdoor slopes on loggias, sometimes forgotten or postponed for a long time, but this cannot be done, since the environment does not affect the windows. The internal slopes are mostly needed for beauty, and the outer performs very important functions.
Installation foam over time loses its properties
A mounting foam is used with a fastener and sealant when installing windows, but it loses its properties over time while under sunlight and rain. Water that enters the seam and destroys the thermal insulation properties of foam. In winter, the foam is expanded and decreasing from temperature drops, and this makes mechanical damage. Therefore, it should be protected by the mounting foam finish, it will also help the plastic windows last longer.
It should be protected by mounting foam finish
During the installation of windows, workers can damage window openings by making cracks and potholes. Therefore, they need to be closed with finishing, so that they do not increase under the action of climatic conditions. Also covered slopes look more beautifully open seams with foam spoked.
Finish need to do high quality in order to even under the influence of precipitation and frosts, it served for a long time. The properties of heat-insulating sealant and the slopes will not give, condensate will appear.
Article on the topic: Fittings for the choice of plinth - what to pay attention to
Plaster slopes
It is necessary to apply the solution so that there is no strong drops
- First of all, you need to dissolve a dry mixture for plaster with water. Then, with the help of a construction mixer, mix thoroughly. As a preliminary preparation, you can apply a layer of prime.
- At the second stage, a small spatula is applied to a large spatula and applied to the base with a bias of 45 degrees. It is necessary to apply the solution so that there is no strong drops.
- After that, you need to give the printed layer to dry. Then, with the help of sandpaper, it is necessary to sweep the surface from irregularities, and apply a layer of the finish solution. You can use the same solution as an finishing solution, you only need to make it more liquid, it will block the remaining irregularities and cracks. After drying, you need to repeat the process with sandpaper.
- At the last stage, it is possible to paint the slopes of the loggia with the help of water-level paint. In the process of work, you need to ensure that the solution and paint do not fall on the window and glass.
Metal slopes
This type of material is not affected by rust and corrosion.
For the outer decoration of the slopes on the loggia, a metal coated with a polymer is used. This type of material is not subject to rust and corrosion, serves excellent protection of walls from drops of temperature and wind gusts. The high-cost material will pay off a long service life.
Plasterboard finish
For the manufacture of plasterboard slopes on the loggia, it is necessary to apply a resistant to moisture plasterboard.
- Before starting work, you need to remove the old plaster from the base and process the primer, after that you need to wait a couple of hours.
- Using a level or plumbing, the line along the loop of the loggia window is fused. Then you need to fasten the plastic bar of the P-shaped form, along the edge of the drawn line, for this, the screws and the screwdriver are used.
- The size of the dump of the loggia can be found, measuring, distance from the bottom to the top corner of the window. Then the width is measured with the long line, both sides are needed. Then the blanks are cut from drywall on these sizes.
- At the next stage, the prepared glue was applied to the primed base. For better fixation of drywall in the profile, silicone or acrylic sealant is added. The desired angle is set, for this it may be necessary to need a square to set the exact size can be segregated a bit to the base.
- Then there are markers for fastening the top of the slop, and is screwed to the profile window. The upper part of the gypsum will be a little in the frame. Working with drywall on loggia trimming of protruding plasterboard parts.
Article on the topic: We independently make curtains from Beads do it yourself
On the loggia you need to apply the moisture-resistant plasterboard
Finishing with plastic panels
The appearance of the PVC - the panel looks very good with plastic windows on the loggia, it turns out something like one whole. When choosing panels, it is better to pay attention to the outer materials, as they do not fade.
- First of all, it is necessary to prepare the surface, repeat the old plaster, harvest the required size of plastic parts.
- Then the perimeter of the loggia window is covered with a tree with rails, then the profile latch is screwed to refuel the plastic panel.
- Then the plastic panel is inserted, while the profile in the form F is used in the corners.
- Such a slope can be additionally insulated, this is done by a mineral wool, which is placed with a wall and panel. For this, a small amount of wool is used to avoid plastic fuses.
- In the case of non-accurant joints, it is better to wash them with silicone.
Appearance PVC - panel looks very good with plastic windows on loggia
Plastic has a beautiful smooth surface so that additional finishes are not needed, while the color range of the proposed material is very big and there is an opportunity to choose any color.
The slope from the plastic is very good, primarily due to the same expansion coefficient. The material fits tightly to the window and eliminates the appearance of the gaps. As a plus, it can be considered that there is little time on the device of the panels on the loggia. With such work, it will be able to cope even the beginner, the most important thing is to install the guide level and accurately cut off the panel.
Outer foam slope
From the foam make the slopes of the loggia is easy
The outer slopes of the loggia is better to do with the help of polystyrene foam, which is easily processed, and make the slopes of the loggia will be completely simple. The load on the slope is always big, so the materials are selected more carefully.
- To begin with, glue is prepared, which must be mixed well (so that there is no lumps), but he remained thick.
- Then, the base surface is processed with soil, all the slots are embarrassed and the segments of the foam are cut.
- In order to get the best clutch of the wall with foam plastic, we melt the base.
- Then the glue is applied with a toothed spatula on one side of the foam and glued onto the wall, so that the surface is to be smooth can be checked.
- Having finished the foam device, all joints are additionally labeled with glue. In the process of gluing the foam glue, it is better to apply a little more, the superior will then be deleted, the main thing remained emptiness.
- After that, it is necessary to give some time to stick the glue, and then walk the thin layer on top of the foam, the grid of fiberglass is sampled and perforated corners are installed.
- When the glue is completely dry, the dumping of the loggia is processed by primer. To avoid stains on the glass it is necessary to make the edge of the glass package with paint scotch.
Article on the topic: Why do we need wood processing by mourn and varnish?
In conclusion, plums is fixed
For the finish finish, you can use paint of any color or acrylic paint with small pebbles.
In conclusion, the drain is fixed.
If the separation of the dust of the loggia of the foam is performed correctly, then the appearance of the slopes will be sufficiently beautiful and insulated.