Choosing than to cut the plastic plinth, prefer the usual and fairly simple in handling tools. We are talking about familiar to all the masters of the hacksaw metal.
However, this is not enough, as it is required not only carefully make a straight cut, but also exactly and correctly cut the corners.
For high-quality execution of this operation, such a device is needed as a carpentry stub. It is with it that you can cut an angle of 45 or 90ͦ. Of course, you can use the grinder, but in this case the cut line will be quite wide, which is not always convenient.
Choosing a suitable tool
Completing the repair and finishing work in the room, each specialist wonders "than to cut plastic plinth." The answer depends on how important the quality of the edge obtained is.
It will be the highest quality when using the metal hacksaw. Its blade is quite subtle and durable, therefore, the cut will be thin and smooth. The edges will not crumble, and cut the plinth will be convenient.
If the edge quality does not matter much, but the speed of work is important, many builders and finishers use the grinder.
The thickness of her disk is such that the cut line will be quite wide, but the edges will not always be able to please the owner with their quality. However, using this tool, you can make a fairly large amount of work in a short time.
Bulgarian will leave a smooth edge
Cutting outdoor plinth can be even scissors for metal, if there is no other tool at hand. Such manipulation cannot be called comfortable, but if necessary, the master can easily cope with the task.
In any case, the cutting tool must comply with certain requirements, including:
- safety;
- efficiency;
- accuracy.
To use this or that device follows after you have been convinced of its productivity and the possibility of quality performance.
Alternative to standard species
The correct tool will not leave the jar on the edges of the cut
Article on the topic: Bathroom 2 square meters. m. - Small secrets of successful design
After the PVC plinth is cut, there should be no chips on the edges. The correctly selected tool that will have to cut the base of the plinth, does not cause cracks or significant irregularities at the edges of the edge.
No less popular with the builders electric jigsaw, but it is possible to use it only when working with panels. Plinth, whose feature is quite thin walls, it is impossible to cut quality with such a device.
A sharp move and rather large teeth will lead to cracking of the product, making it installation impossible.
The most secure and efficient after the cutting metal is recognized as the usual mounting (bulk) knife.
Cutting thin-walled plinths that are attached to the floor, such a tool is performed quite quickly and simply.
Floor PVC plinths, equipped with cable channel, is easiest to be cut with a conventional manual jigsaw. It will allow you to make a clear cut, keep the edge edge as possible and prevent the slap cracking.
Cut the bar closing cable-channel, you need after the preparation of the plinth itself. When it is cut exactly in size, you need to install a bar and only to cut it after that.
Laying the floor base starts from a far inner corner. If the length of the wall is large, then you will have to use the connecting plug, and then trim the strip of the plinth, without reaching 1.5 cm to the edge of the wall or 0.5 cm to the next corner. Regardless of the number of angles and compounds, cutting is carried out strictly in a straight line, which greatly facilitates the performance of work. Detailed manual for cutting and docking plinths See this video:
Working with ceiling plinths
Beginner masters often ask how to cut the ceiling plinth to form the inner or outer angle correctly. Ceiling plinth cannot be accurately cut without the use of stusl. This device allows you to perform the cut at any desired angle.
Article on the topic: What is acrylic primer: species and application
Perform the proper trimming in strict adherence to geometric shapes. The use of stusl makes it possible to get a perfectly even and accurate cut.
Scheme of work with stub
The device with a complete set has grooves created for cutting blanks at an angle:
- 45 ͦ;
- 60 ͦ;
- 67.5 ͦ;
- 90 ͦ.
To perform the operation, during which you need to install the plinth in the corner, you need to trim the panel strictly under 45 ͦ. In this case, two details folded together will give a full-fledged 90 ͦ try creating both external and internal angles. For details on how to properly cut the plinth with the necessary angle, see this video:
Cutting of any plinth (ceiling or outdoor) is performed after determining the correct slope.
From the configuration of the corner itself, the location of the cut on the inner or outer surface of the part depends.
In cases where there are practically no uneven and strict angles in the walls of the walls, it is not necessary to use stupid. It is better to trim the plinth manually using the usual greasy (stationery) knife.