If you constantly flow water in the toilet, then this circumstance can withdraw anyone. Not only is the noise from the water annoying, and at night it seems to be a roar of the waterfall and prevents from falling asleep.
Diagram of the drain tank.
Another negative phenomenon arising from the above situation - rust strips in the toilet. Clear such quite difficult. But, even by coping with this task, successfully, you can not avoid her repetition, since when weaving the water you are guaranteed the incessant struggle against rust.
As a result, such a breakdown of the pipe in the toilet is constantly moathed, since condensate is going to be collected on their surface. Agree that this is also an unpleasant fact. So, how to deal with this misfortune and what is its reasons? We learn later.
Instruments:
- pliers;
- spanners;
- knife;
- screwdriver.
The most common cause
The most common reason that water constantly flows in the toilet, is a tank overflow. And excessive fluid is leaking through overflow. And this may happen due to certain circumstances below.
Toilet bowl overflow can cause leaks.
- It is possible that the tank design has occurred deformation of the valve laying. This happens in cases where the tires lost elasticity as a result of the past time and cannot block water tightly.
- Another version of the problem may testify from insufficient pressing of the gasket to the valve hole (output). The gasket can be of good quality, but not tightly pressing, with the result that water flows.
- The third possible problem belongs to the state of the hairpin, holding the lever float in the valve. It can be rusted either overgrown.
- And finally, the crack in the valve body can also affect overflow. The crack in the valve is possible only in the plastic version. If you have a valve made of brass, then this breakdown will not touch you.
Article on the topic: Guidelines for the construction of the design of the frame house with their own hands
It concerns possible reasons. But how to determine them? To start, spend a simple experiment.
- To do this, remove the tank cover. Next, slightly (about 1 cm) lift the float. And if the water ceased to flow as a result of these actions, then you found the reason.
- Now, in order to bring the state of the float and lever to normal, you just need to get the float lever on everything gently. Thus, it will overlap water earlier and the problem will be solved. Water no longer flows.
We are looking for the following reason if, after the above actions, flowing did not stop, it means that it is necessary to inspect the valve.
First, pay attention to the hairpin holding the float lever.
Tech elimination scheme in toilet
It must be in its place and have no damage. The hole in which it is located should not be spacious and breaking.
Further actions depend on what you have discovered when inspection. If the breaking of the stud, then it can be replaced with wire (copper). If the hole does not correspond to the norm, then you can not do without the purchase of a new valve.
And one more important advice: if you went to the new valve, then take with you the old (for sample), as in modern building markets a large selection of sanitary accessories (it is very easy to get confused and choose the appropriate).
Another reason for the flow of water in the toilet
If you were convinced that the water level in the drain tank does not reach the overflow mark, and the water flows anyway, it can occur due to the failed bolt, tightening the toilet and shelf.If it is made of steel, he could simply rust if from plastic, then burst. It is not clear that the manufacturers of the toilet bowls of the last century were focused on, when they equipped brass kits with steel bolts. Note that it was originally assumed that they would be used in cold water, it means that their destruction will inevitably come. The only question is what happens before or later.
Article on the topic: Water Heat Connection Schemes
You can solve such a problem very simple. After seeing the existing fittings and finding out that its condition is close to the ideal, and only bolts left, it is necessary to simply replace them with new ones. And even better to purchase the entire set of reinforcement. Its cost is not high, so you will not suffer special financial costs, but to save yourself from unnecessary problems with the leaking of water.
Third possible problem
Replacing the old pear to the new to deliver the toilet to the tech.
So, they found out that the water in the tank does not reach the level of overflow, all bolts are in good condition and are in their place. But the flow still takes place. What to do?
Perhaps a problem in a pear. Fluent flow water from the tank in the toilet does not give a pear, made of rubber.
By lifting the handle on the tank, you thus raise a pear and she flowing water, goes into place. After a certain time, rubber loses its properties, such as elasticity. Its surface acquires stiffness and cannot be tightly located in the saddle, i.e. Shears water.
An ideal solution to the problem will be replaced by an old pear on a new one. Its fastening is carried out with the help of a thread, so, turning the pear counterclockwise, you can easily unscrew it.
By choosing a new pear in the store, pay attention to all samples offered to you, and choose exactly the surface of which will be the most soft. In another case, you can again disturb the flow of water in the toilet.
If you buy a new pear you do not have the opportunity yet, you can use a way that will allow you to take a pear and pick it up to the saddle. To do this, you use something small in size for all, but a good enough, such as a nut.
Article on the topic: Apartment at 10 square meters. M: Compact and bright design
In conclusion, I would like to note that it is impossible to cover all possible problems regarding the flows of water in the toilet, as well as ways to solve them. Each sanitary device of this type has individual characteristics, so it is possible to understand why water flows in it, it is possible, only well studied its design and finding a problem.
And if you do not under power to do it yourself, it is best to seek help from professional plumbers. They are also definitely subject to any models, and the solution to the problem will not wait long for a long time.