The installation of PVC doors can be performed on its own. To do this, it is necessary to clearly follow the technologies of their installation.
Plastic Door Device Scheme: 1 - Major Frame, 2 - Door Blind, 3 - Hinge, 4 - Translucent Filling, 5 - Disposable Filling.
Installation of the door box
Required:
- level;
- roulette;
- chisel;
- electric drill.
Assembly and installation of the door frame: A - assembly of the box; B - fit boxes to the wall; B - fixing the looped jamb (1 - looping pin; 2 - seal).
First, the verticality of the wall is checked and the dimensions of the doorway are determined - both in width and height. Then the calculation is made. For example, PVC door has a width of 90 cm and a height of 200 cm, it means that the width of the boxes is: 900 + 25 + 25 + 5 = 955 mm. At the same time, 25 mm is the thickness of the door frame, and 5 mm is the door gap. The height is: 2000 + 25 + 3 + 10 = 2038 mm, where 3 mm is a gap from above, and 10 mm below.
Door box is assembled on the horizontal surface of the floor. The upper ends of its racks need to be cropped at an angle of 450. On one of the side racks there is a docking place with lower and top loops. In the box with the help of the chisel, the grooves the required depth is cut. Then the holes are made for screws for screws.
Preliminary work
Required:
- hammer and nails;
- electric drill;
- self-tapping screw;
- mounting foam;
- Malyary Scotch.
Diagram installation of the door closer.
The installation of metal-plastic doors is carried out after the finishing works of the floor covering. The installation of PVC doors begins with a blocking of several nails for further fit. It must be collected in a horizontal position.
To do this, in places docking are made using a hole drill, which must have a diameter of 1 mm less, under the self-tapping screw. At the same time, the pole from the loop side is first set. And the rack from the lock side is mounted by the arrival after the installation of the canvas. Door loops are screwed after mounting the box.
Article on the topic: How to make a measure of the stretch ceiling with your own hands?
To align the entire block when installing plastic doors, wooden wedges are driven into the gap between the opening of the opening and the block frame. You need to drive them carefully to avoid damage to the frame.
To protect the visible part of the door frame and the canvas uses mounting foam. It must be evenly applied throughout the perimeter of the box. Related areas of the door are rushed with painting tape to exclude foam on them.
Door installation
Required:
- Perforator;
- dowels;
- screws or screws;
- mounting foam;
- Plastic platbands;
- hacksaw;
- Stuslo;
- glue.
Installation of PVC doors begins on the loop side.
If the support door is stone, the holes are drilled in it and the dowel is driven. Then the screws are neatly twisted and the evenness is checked. After that, the adder is attached. It is fixed by several fasteners. First, the holes are made, the dowel is inserted, then screws screwed. Next is checked, it is exactly the door in the frame. If everything is in order, then on each side 2 additional attachments are made.
Then the door is installed in its place. If she is with a threshold, then 2 fasteners are made through it. At the same time, the upper bar is not necessary. Also, the threshold can be performed independently if it is not included. If the threshold is not needed, the door is fixed by means of a special upper mount.
Using wooden wedges, you should cut off their protruding ends. After that, the space that turned out between the door frame and the wall is filled with the mounting foam. It should be remembered that the foam increases several times in the amount. After it dries, its excess is cut.
The execution of finishing works of interroom doors is carried out in a day after a mounting foam was applied. To close all defects and slots between the wall and the box, plastic platbands are installed. For their dosilets are used 2 methods.
Article on the topic: How to make steps for the porch with their own hands?
First, they can be styled at right angles, staining or toning spils with varnish. At the same time, they can be counted, both in the horizontal direction and vertical. Secondly, platbands with a rounded surface are roasted at an angle of 450. Plastic platbands are mounted on a surface having a slight irregularity using glue.