The clamp that can be seen in the figure below is a special kind of clamp that is customary to use during the fixation of various parts, this tool can be used for dense pressed elements to each other. There is an indispensable clamp in the process of sawing, breeding the teeth of the saw or its sharpening, perfectly helps such a method and when gluing different elements. Clamps can be made with your own hands only if the master is familiar with its device.
Clamps are considered a simple auxiliary tool, but they are indispensable in cases where it is necessary to attach strength and at the same time working carefully, for example, when gluing or sawing.
This tool has a major frame, a sponge for clamping, a mobile element and a lever component. The mobile part with the help of threads can change the step between clamping sponges, and the lever is responsible for how much the clamp will be carried out. There are other varieties of fast-following tools, including a lever device designed for fixing. The basis of its design levers and eccentrics, however, such a device is difficult to make on their own.
Tools and materials for the manufacture of wooden clamp:
- Threaded stiletts;
- Reiki;
- plywood boards;
- Nut.
Technological process
The main materials required for the manufacture of clamps.
To make a clamp, 2 studs should be used that have a thread, their length should be equal to 200 mm, and the diameter is 5 mm, 2 more studs will be used, which have the same section, but a length of 120 mm. Nuts suitable on dimensions should be prepared; Boards from plywood, the size of each of which is equal to 15 × 150 × 200 mm, as well as 2 rails with dimensions of 20 × 40 × 240 mm. It is preferable to use bars made of solid wood wood, perfectly suitable for the manufacture of these elements ash, birch, oak or beech.
Article on the topic: How to remove rust from instruments, bolts and nuts with your own hands
Similar wooden clamps are fixed to the working surface. In the bars speaking as fastening the clamping part, you need to form 2 holes, it is necessary that the hairpin with nuts can press them to each other.
The stability and reliability of the device will provide the location of the lower bar. Plafthd, and the upper - edge to the base of the working surface.
Then you should install boards from plywood, and to apply a bar, strengthened to the tabletop. The lower edge of the plywood should be 3 cm below the bar himself. Three blanks should be drilled, and in the hole after it will be necessary to insert studs.
Metal hacksaw to modification and clamps obtained from it (after modification).
Next, one board will have to strengthen the lower bar, and the second plywood will act as a clamping element. Such clamps produce the capture of a movable plywood stripe. Short studs must be applied to fix the tool to the surface of the countertop, and the longs will define the workflow of the device. The nuts will perform as a lever, which fixes the movable part and adjusts the power of the clamp.
If you make clamps with your own hands, then you should consider that such tools are somewhat less reliable for those that were purchased in the store. Clamp is permissible to obtain, applying the hollow housing designed to work on the metal. For which it is necessary to use a sliding tool body, 2 studs that also have threads, as well as nuts. You will need to insert stiletto into the clamping connectors.
Nuts to wear from the inside of the device. Such a clamp will have two sizes, since the steel frame of the hacksaw is able to be laid out in 2 positions. For the reason that the body is able to be laid out, it will become overwhelmed in the process of clamping nuts. It is possible to avoid this if the folding part will be reliably wrapped with a tape. The versatility of such a device is that it can also be easily turned back into the hacksaw if necessary. You can use steel fasteners as fastening the sliding part of the hacksaw, it will be much more reliable. In fig. 3 You can see the hacksaw to modify, and in Fig. 4 - already after.
Article on the topic: Foundation for the fence: how not to bury extra money
It is possible to make a clamp at home, but you should not use the tool at the limit of its capabilities, and otherwise it will last long.