Repair of plastic doors: what to do if the door has checked

You can perform the repair of plastic doors yourself, correctly setting the reason and following the instructions.

Poor-quality door closure

Repair of plastic doors: what to do if the door has checked

Modern plastic doors are reliable, perfectly retain heat and cut off the noise. With them there is no draft, the canvas is durable and sufficiently heavy so that the fittings worked confidently and tightly pressed the box. However, the repair of plastic doors is required quite often. If the structural elements are not damaged, the glazed windows are not broken or there are no deep "shells" over the surface, the design allows you to solve problems. But even in some cases, such repair can be made with their own hands.

Adjustment of PVC bells

The most common problem with which the user faces is the door stops normally closed or well opens. This is due primarily to the work of the loops. The door can be saved, since cases when accessories are chosen without a safety reserve - not uncommon.

It may also be that the loop is applied, which is not calculated on the existing mass of the sash. Perhaps not due to the fault of the manufacturer - just the seller carries out the door with a heavier glass package, which was planned by the loop developer. If the door saved, it is solved in several ways.

Loop Adjustment

The operation is quite simple and visual. On the loop there are two adjusting screws that are responsible for the position of the canvas. Repair of plastic balcony doors is reduced to the selection of the optimal position. This is done as follows:

Remove the plastic decorative lining from the loop.
Two adjusting bolts under the enemy hex key are responsible for the position of the sash. Upper adjusts vertical, side - horizontally.
Adjustment begins with top loop. Turn the head of the side screw clockwise, pressing the shutter to the box.
If it does not help, adjust the lower loop, rotating the screw against the clock.
In the case when the horizontal adjustment range is not enough, you can lift the leaf up using the screws of the corresponding adjustment. In order not to create a loop load imbalance, you need to twist / unscrew the screws to the same extent on all units of fittings.

Article on the topic: inexpensive fence for giving. What is cheaper to make a fence?

There may be a situation where the adjustment range is missing, then you should contact a specialist to replace the loops on the constructs of another type or do it yourself.

Glass adjustment

Liberation of the glass package

Repair of plastic doors by selecting the position of the glass package - rarity. This can already be called the elimination of the results of the negligent work of the collectors. Schedule using such an operation is liquidated like this:

We celebrate the current position of the closed door with horizontal lines (a pencil is carried out, on the frame and the vertical stand of the sash).
Remove plastic strokes. It should be noted, which position occupied each of them in the frame.
Wooden or plastic blades shift the glass. By changing previously conducted horizontal lines, you can understand which direction the sagging changes.

Double blades
Fix the glass with plastic gaskets. You can use other unbating or non-discovery materials. For example, take pieces of textolite.
Check the system. If the door closes / opens better, set the strokes.

You need to hit the stroke into place neatly, observing the original position. This is due to the fact that some collectors can cut off the parts several unequal size and the stacking of the stroke can damage the glass package.

If nothing helps

Contact specialists

Cases of the negligent installation, as nor sadly, are found. Most often the process is happening like this:

The installers incorrectly mount the main construction, with disturbance of the corners;
regulate accessories, often twisting / spinning everything to the limit;
The doors are closed / open, work is handed over to the customer;
Over time, if the door has saved, the adjustment will not help, because the loops simply have nowhere to shift.

To determine such problems, it is better to contact the specialists, since it is easier for them to assess the position of constructs. It may help the replacement of the loops, but technically most often the task is not easily solved, as it simply does not have the necessary gaps for adjustment. It is necessary to act by changing the position of the entire block.

Removal of decorative lining

Handle works badly

With accessories, the operation is easier. If the handle works or badly work, most often the repair of the plastic door is made by several simple actions:

When breaking the fastening screws (the most common reason), you need to remove the decorative handle lining. This is done with a light lift or turn. After you need to use a screwdriver to push fasteners.
If the handle works tight - possibly dry grease. In this case, the repair of a plastic balcony door comes down to lubricating the mechanism.
Sometimes failures in the work - the result of breakdown parts of mechanics.

Set of fittings
For example, a latch or lock does not work. You can replace the whole knot, but in specialized stores it is realistic to find spare parts.
The cause of effort when closing and the bolt can be conclusted in problems with the seal. Therefore, the repair of the balcony doors is better to start with checking this "zone of responsibility."

Problems with a seal

It should be immediately noted that the plastic door seal is an element requiring periodic maintenance. If this is not done, it dries, crumbs, loses flexibility, in a word, fails.

Replacing the seal

Some types of seal have a clear period of work, after which it is necessary to replace. Another enough service every six months-year.

The category of fine repair includes a state check and installing a constructive in place - a rubber "tube" often falls out of the groove. If damage is observed due to strain or destruction from time to time, it is better to replace the seal. To do this, you should find the desired type, to buy sufficient length, and install everything on the "regular" place will be difficult - you need a little accuracy and patience.

Heavy Damage: Partial Destruction of Glass Package

It should not be done on their own. It is better to refer to the seller of the product in order to order a new package entirely. But, if for a number of reasons to do it is impossible, the problem of one broken glass can be solved.

Such a repair is reduced to the dismantling of the glass package, the accurate removal of lateral sealing from the end and no less accurate removal of the residues of the broken glass. After that, the new, desired size is cut.

Installation is made in conditions of minimal dust presence. New glass and double glazing should be thoroughly washed. Installation is carried out on the sealant along the contour, transparent. After that, the end of the glass package is also isolated. This can be done like using a sealant, as well as a special heat shrink film.

Important note: To eliminate the danger of condensate formation (perfect sealing, it does not turn out most often, and the air between the glasses contains moisture) can be placed between glasses a little silicogel, which is put in shoes to absorb moisture.

Heavy Damage: Scratches and Strong Turning On Surfaces

Glass Polishing Tool

Perfect recovery will not work. But if you do everything neatly, you can achieve a fairly acceptable appearance.

Waste can be eliminated by polishing with a special paste or use the tooth whitening effect.
Deep scratches are neatly cleaned, so as not to hurt the intact zones, clean and degrease. After that, you can pour the zone with liquid plastic Cosmofen, align the surface and refuel.
To eliminate damage to the laminated coating, there are special pencils, including color.

As you can see, the repair of plastic doors faults is a completely accessible operation. You just need to do everything neatly and in accordance with the instructions.