Each domestic master knows the price of a homemade sofa, because It is from him that the quality of sleep depends. To make this element of the interior, you will not need a lot of time and effort, but you need to fully follow the step-by-step instructions.
The diagram of the internal filling of the tacht.
Selection of material
At the very beginning you need to choose the type of couch, which is to be made with your own hands. Designs may not only be simple, but also very complex. Moreover, difficulties almost always consist in the number of parts used, so in practice it only takes time. It is better to take an average option for the sample, which is easy enough, and it will be necessary to use all the main techniques.
Technical characteristics of chipboard.
After the ottta is defined, you need to choose the material. For this work, only 2 options will be suitable:
- LDSP is a simple inexpensive material with a huge color range. It is worth very inexpensive, and you can get in any city. The laminated stove has several minuses: low strength indicators, low design qualities and poisonous emissions in the air until all edges are closed.
- Furniture shield - high quality and good tree. Due to the specifics of manufacturing, the material is performed completely environmentally friendly, and also has very high strength indicators (almost not inferior to the array). Only 2 minus the shield - there is far from every city, and it is possible to buy even less often because of the high price.
For clarity, an average density plate and a thickness of 20 mm will be used, which is almost always used in factory conditions. Kant will be used will be standard paper on a polymer basis.
From sawing before mounting
Sofa assembly option.
Tools and materials:
- roulette;
- electrolovik;
- screwdriver;
- simple pencil;
- LDSP;
- galvanized corners.
After the final choice was made, you need to cut the chipboard on the diagram prepared in advance:
- 700 * 800 mm - 2 pcs (headboard and foot);
- 700 * 1795 - 1 pc (bed);
- 200 * 1800 - 3 pcs (stiffery strips).
Article on the topic: Wallpaper for the children's room Combined: how to combine in the room, photo, for boys, for girls, video
In each segment, except for the bed, you need to make special coupling grooves. The depth of the groove on the carrier segments is 170 mm, and the rigidity planks are 30 mm, due to which the perfect joke is obtained with a barely noticeable seam. They will be located at an altitude of 400 mm on the floor level, and at the site of the side ribs of stiffness (improvised replacement of the back) is made an indent of 10 mm, after which the groove is formed.
The combination of the sofa design is easy to easily, so everything can be done properly. First, the carrier design of 2 supports is collected, after which the back is installed.
Drawing round ottoman.
After the joints are all formed, you need to use steel galvanized furniture corners by 2-3 screws. They are recorded in the lower (hidden) part of the design at a distance of 15-20 mm from the edge so that it is not visible. Also during fixation, you need to carefully treat tagging so as not to drag. If the work goes the screwdriver, then the ratchet must be put up on the most sensitive level, so that when the peak point is reached, it will just stop. When performing a screwdriver and is completely resistant, which will be the signal to the transition further.
Before screwing the screw, you need to make a hole by 12-15 mm, for which the drill should be a deep voice or drill to tie the blue tape at the desired level. In any case, you need to seek perfect quality so that nothing can be seen outside.
At the very end, all the ribs are sofas with a special cat. For the joint, an ordinary iron will be required, which "smoothes" Kant in its place (the polymer base is melted and provides a reliable coupling with chipboard). It is advisable to use the help of another 1 person or fix the Kant to the tape at the edges, because After stroking, it will be impossible to fix something.
Article on the topic: "Three doors" (Tambov) - directory of entrance and interroom doors
Additional aspects
If there is a desire, you can install boxes under the sofa. Quantity depends on preferences, but it is better to make at least 2, because In this case, you do not have to make great efforts to extract them. The rollers will not be used because of a small height, so the whole base must be as homogeneous as possible so that no interference has been created when extracting.
Sometimes the side edge, headboard and foot sofa are abundant for beauty. Upholstery materials can be used any, and only foam rubber (batting will not give the desired effect as a volumetric filler). The glue for the foam rubber can be used any, but the stapler is desirable to fix in 2 layers, because The stove is quite unreliable for such works.
Make a sofa with their own hands will be able to anyone, but here we need a supply of patience, as well as a high-quality tool. Every step is better to think about several times, and then do, because Even a little miscalculation can do in additional financial costs.
Total manufacturing takes no more than 2 days, and if you fill the hand, you can cope in less than 1.