When repairing the bathroom, you must solve the following question: to connect a towel dryer with your own hands or resort to the help of professionals. In any case, you must understand that the connection of the heated towel rail and the pipe is simple.
Installation circuit towel rail on the wall.
Materials for work
You will need:
- heated towel rail;
- trumpet;
- cranes;
- connector;
- riser.
The connection of the heated towel rail provides 2 options for cutting pipes:
- In the heating system and in the hot water supply system.
- Due to the fact that there are almost always hot water in the pipes, most often preferred exactly the second option.
And the process of connecting the heated towel rail to the heating system is best done not in the heating season, because in the lutty frost it is not recommended to overlap heating and lower water from pipes. Otherwise, for a home it can end with poor consequences.
Deciding with the method of connection, you can start connecting the heated towel rail with a pipe.
Connection diagram of a towel rail.
For example, in many homes of the Soviet buildings, the towel rail looks like a zigzag pipe located on the bathroom wall. If you wish, replace it, you can choose the model of the corresponding diameter with the lower connections.
If you have pipes in the wall with only the outputs left, in this case you can install water coolers of water with side connections. Mounting such structures are much more complicated, but they look quite attractive.
By installing the equipment of this type, it takes enough to isolate all the connections sufficiently, because if it is proof, the faults will be very problematic.
Connection of the heated towel rail to the riser
You can even connect the water towel dryer with your own hands.
If you wish, find out how to connect a heated towel rail, you should follow this scheme:
Methods for connecting a water heated towel rail.
- Dismantling of an old device.
- Installation of cranes.
- Installing a new device.
- Check the quality of installation.
Article on the topic: What wrote curtains for curtains in the interior look like
If you properly approach, then the entire procedure can be performed within a few hours.
Next can be disassembly . Deleting the old water heated towel rail, you can proceed to the dismantling of the new one. Initially, you need to overlap the supply of hot water into the pipe where the device is placed. To do this, it is best to contact the HOWE, but it is possible to do this and independently, having coordinated this question in advance, for example, with the chairman of the cooperative.
Models that are not considered an integral part of hot water pipes are dismantled by unscrewing threaded connections. In the event that the thread "baked" or a heated towel rail is welded to the pipe, it is necessary to trim it with the help of a grinder.
When dismantling, you need to take into account the following: trimming is carried out with such a calculation so that the pipe section is sufficient for the thread.
Installation of shut-off reinforcement
Then proceed to the installation of cranes. After the old product is removed, it should be done on the residues of the pipe a new thread of the appropriate diameter. If the thread is in order, you can install shut-off valves - cranes.This is done with the goal so that the intensity of the device can be adjusted when the cranes can be opened or closed. And also to repair, in the event of its flow or replacement, when it is necessary to overlap water and make the necessary actions.
You need to choose fittings depending on what type of connection is in the heated towel rail. With the help of linen winding, all threaded connections are compacted. For conical threaded connections, use FUM tape (as it is an excellent connector).
This is followed by the process of connecting the heated towel rail to the pipe. By connecting the device to fittings, you must tighten the attachments so as not to damage the thread. Connecting a towel rail to a riser or wall occurs with the help of clamps or special telescopic holders.
An important point in this case is to properly select the distance from the wall to the axis of the truck of the unit:
- When the pipe diameter is less than 23 mm, the distance must be 35 mm and more, and with a diameter of pipes 40-50 mm, the minimum distance should be 50 mm.
- Connected device Be sure to check for tightness. To do this, you need to spend a trial start. This device can only be used if there are no leaks.
Article on the topic: How to make an assembly on the curtains: with the help of a curtain ribbon and manually
Connecting electrical equipment requires separate attention. It is especially important to correctly connect the device to the electrical network, since it is in this way that a short circuit or ignition can be avoided. In general, it is necessary to connect the device in compliance with certain rules.
Grounding
The mandatory moment in this process is the grounding of a heated towel rail, including connecting the device through a protective shutdown device.
If you decide to connect an electrical device to a socket, which is located in the bathroom, it must have a waterproof housing. In general, if you decide to combine the equipment to the riser, there will be no problems with this.