A bed of wood with their own hands is a cheaper alternative to an expensive bed, which can be purchased in a furniture store.
Before you start work, you need to remove the sizes from the mattress, pushing off from these numbers you can cut the boards.
Such a bed is easy to design and manufacture, in addition, it can be done on its taste, to fit the sizes.
Required tools and materials
The conditional sizes of the bed must be equal to the mattress, so the base is taken as the bed having a size of 2 × 1.5 m. As a material that is necessary for building a frame of this furniture, you can take a beech, larch or pine.
The following tools and materials will be required for the construction:
Tools for the manufacture of wood furniture.
- Electrolzik.
- Screwdriver and drill. It will be necessary to perform the work of varying degrees of complexity and destination, so you should be stockpons of additional drills of different sizes.
- Hammer and chisel.
- Wooden hacksaw.
- To eliminate rough surface roughness, plans are needed and sandpaper.
- In order to mark the bed details, a pencil, roulette and corner will be required.
- Metal fasteners and wood screws.
- Alcohol or acrylic veneer, joinery and varnish.
- Sideboards in the amount of 2 pieces with dimensions of 250x30x2 cm.
- Boards in the amount of 3 pieces, which will be required to create a headboard and the end side of the bed. Dimensions of boards are equal to 200x30x2 cm.
- For carrier and support legs, boards are needed in the amount of 5 pieces (4 will go to carriers, 1 board will be the supporting leg). Sizes of bars - 200x4x4 cm.
- Warehouses are needed to cover and securing boards from the head of the bed. Therefore, 27 rails will be required, sizes of 150x4x2 cm. 2 boards will go to securing the head of the head of the head, the rest will be used for overlapping plates.
- Brush and roller.
Article on the topic: Build a balcony on the first floor: how to make it right
Assembling Furniture Frame
The frame assembly will include a phased performance. Getting started, it is necessary to make a frozen mattress that will be used . It is necessary that the mattress is free, but in the bed should not be gaps between the mattress and the walls of the furniture.
Drawing of the bed with sizes.
Next, you need to cut the boards in the number of two pieces of the corresponding size. They will go for the construction of lateral sides. Similar operation should be done to cut two headboards. From the received boards, add the right rectangle, that is, with straight corners. In order not to still fixed the frame, it should be fixed with the help of faces and spikes.
You should make grooves for connections that are 5 cm in depth and from 2 to 3 width. Teams should be lubricated with joinery glue, after which it is to ensure their connection. After the alignment, they are fixed using clamps, after which you should wait until they are dried.
The above design is an example of a conventional connection used in the joinery craft. If such a connection option is difficult, then the sides of the bed frame side can be consolidated with thickening fasteners. To this end, in the end side of each board, including at the edges, you should drill holes, the diameter of which is equal to the diameter of the spike. The spikes and holes should be wrapped with jointed glue, then the framework is taken on.
In addition to the carcass, the bed of wood, like any other, should have legs. Remembering the drawing specified earlier, you should take suitable bars or cut them off. The legs are fixed outside or from the inside of the frame and are located in each corner. In addition, the legs can be pasted directly into the frame.
To set the legs into the frame to use a studded fastening. It is more suitable to consolidate such furniture, moreover, this compound will not lead to loosening the design of the bed. For wide beds with a capacity of two people, a safety leg should be made to which part of the load will be leaving. In addition, the bed do it yourself thanks to the fifth leg will not fail, since the load will be distributed evenly. For the fifth legs, a longitudinal board is attached in the middle of the future bed, a leg is installed on this board.
Article on the topic: How to glue phlizelin wallpaper with your own hands: technology (photo and video)
The last stage of work
To build a bed with your own hands and complete the work on it, you should create a grille called the lamella mesh. Her main task is to hold the mattress, do not let him fall into bed. To this end, on the inside of the bed on the end boards and sidewalls, a lock rail is mounted for fasteners. Marking in height is made at least 10 cm from the top edge of the bed. Instead of this rail, you can install a metal corner.
Wooden bed assembly scheme.
After that, the timber is taken for the manufacture of lamellae, which is mounted in the inner bed. Rakes that have 150x4x2 cm sizes are mounted on the resulting frame. Rakes are mounted perpendicular to the length of this furniture, the distance between the rails is 5 cm.
After collecting the bed, it is necessary to perform a skeleton of the frame, after which it is covered with varnish. The color of the furniture must be chosen in advance, it must be pleasant for the eyes and fit into the surrounding interior. For bedrooms, it is preferable to choose soft and delicate colors.
After the skeleton is performed, the surface must be treated with a veil, after which it is covered with oil, and then apply oil or pentaphthalic paint. After drying, the paint goes to applying varnish, but before this surface should be treated with a brush with a brush. When the veil dries, varnish is applied. To do this, in addition to the brush, you can use a roller. Varnish is applied evenly, it is recommended to apply two layers of varnish. After completion of these works, the surface should be polished using a felt or felt sponge.
So that the bed acquired a beautiful view, for squatting and headboard, you can buy a panel plate in special stores. In addition, such a slab can be ordered in carpentry workshops, providing the masters the necessary dimensions.
Thus, the bed with their own hands is easy to design and build. Its construction will cost lower costs than when buying the same bed in a furniture store, and the proper execution of all works will provide such furniture for a long time.
Article on the topic: The ceiling of plastic panels do it yourself - instructions (photo and video)