The washing machine refers to the class of complex household appliances, which means that in the process of its operation, many different problems may occur - in the water supply system, drain, power supply, electronics, etc. Even if you purchased the device from a reliable, well-proven manufacturer, it does not mean that the washing machine will always work properly. A few years of active use, the malfunctions occur even in the highest quality models.
One of the most problematic places of any washing machine is a drain and water set system. It is here that there is a significant proportion of breakdowns. In this article we will tell you about what is happening when one of the filters is clogged, and how this problem can be resolved on your own.
What filters are installed in the washing machine?
In order to maximally protect the mechanism of the washing machine from the ingress of foreign objects, each device is equipped with two filters at once: one is "at the entrance", and the other is "at the output":
- The filter is needed so that rust, lime and other small garbage are needed together with water into the machine.
- The drain filter is provided in order for the pump that the remnants of detergents, threads, buttons and other things are accidentally clogged, accidentally falling into the drum.
In addition to two "mandatory" filters, one additional one can be installed in the washing machine, which cleans and softens the tap water.
How to remove and clean the fuel filter?
The device, filtering water that enters the tank is not installed in all washing machines, but in most modern models it is still available.
Article on the topic: We put the floor from porcelain stoneware in the living room
The filter is a small metal mesh, which settles the fine garbage. Periodically, a thick layer of plaque is growing on the filter, which makes it difficult to access water. In this case, the filter has to be cleaned.
This filter can be detected in the back of the washing machine, where the water regulating the water flow and the bulk hose are located. Before you start work, you need to turn off the unit from the electrical network, as well as disconnect the water set hose. Behind this hose is the fuel filter.
The filter can be easily pulled out by using the passage or pliers. Usually there is a layer of dirt, lime and rust. All these contaminants need to be carefully removed without damaging the device itself. It is best to do this with a toothbrush. It is not necessary to apply any special cleaning products, most often just a large amount of warm water. Clearing the filter, we return it to the place and attach the bulk hose.
You can see this process in the following video.
How to remove and clean the drain filter?
Much more often, the troubles arise with a drain filter, because it is through it that water passes after washing things. All the extracted dirt, fat, as well as the remnants of the washing powder and the air conditioner settle on this device, so blockages in it are formed regularly.
A drain filter, as a rule, is located on the front panel of the washing machine, in one of the lower corners. It is usually located for a small plastic door. If there is no such doors on your washing machine, you will have to remove the front panel to get to the filter. It is removed very easily, as it is not fixed, except for simple latches.
Opening the plastic door or removing the panel, you will see a small item similar to a stopper - this is a filter. It has a special excavation that you need to grasp with two fingers, and then turn the filter clockwise and pull on yourself. In some models you need to rotate the filter until it is unscrewed. Sometimes the drain filter is enshrined with one bolt - in this case, use a screwdriver.
Article on the topic: Production of the arch of wood with their own hands
If water flowed from it in the process of removing the filter, do not be scared - this is normal. It is better to prepare a container or a rag in advance so as not to wet the floor. I pull out the filter, first clean the hole in which it was. Then rinse the filter itself and screw it back.
We offer to see the following video equipment.
If it does not work
This happens when many mud and fat deposits accumulated in the drain system. Then the filter is firmly stuck, and it is almost impossible to pull it in the usual way. However, it is necessary to clean it, so we will try to get to this detail on the other hand. To do this, you need to put the washing machine on the side, then unscrew the attachments that lock the bottom panel. After removing the bottom cover, we find the pump and pull it out. Now you can easily remove the drain filter from the opposite side.
Features of location in different washing machines
Manufacturer | How to find a filter? |
LG. Hotpoint Ariston. Candy Ardo. Samsung Whirlpool | In these washing machines, the drain filter is very low. To get to him, you most likely do not have to remove the bottom panel, since many models do not have it in principle. |
Bosch. Siemens. AEG | For these stamps of washing machines, the standard location of the drain filter is characteristic - in the front bottom of the device. However, to get it, you will have to fully remove the front panel. |
Electrolux Zanussi. | What to extract a drain filter from such a washing machine, you should push the unit from the wall - so you will provide free access to the rear of the device. The filter is immediately behind the rear panel, which is easily removed using a screwdriver. |
Indesit. | This manufacturer places a drain filter on the right side of the device. You can get to it, carefully removing the decorative front panel. This is done using a thin screwdriver, which is inserted between the body of the machine and the front lid. |
Article on the topic: Wall insulation by plasterboard from the inside - do step by step
When to check the filter?
The fact that in one of the filters of the washing machine was formed a blockage, the following signs signalize:
- The display displays a message about the program in the program;
- Water merges very slowly;
- The device dramatically stops washing and does not resume it;
- It is impossible to start the shelter mode;
- Script is not launched;
- Water does not merge from the tank even forcibly.
If you notice similar oddities in the behavior of the washing machine, upon completion of the wash, you need to diagnose the filter state.
Prevention blocks
- A drain filter must be regularly rinsed so that the dirt does not have time to accumulate and easily removed. It is recommended to do it at least once every three months.
- So that the remnants of detergents do not set out in the drain filter, use only proven powders and air conditioners for washing. The poor-quality funds are poorly dissolved in water, so they can be collected in a lump and accumulate in different parts of the washing machine.
- Follow the easel objects in the beam drum to the beacon: in front of the washing, turn the pockets of things and fasten the zipper. Small things and clothing with a large number of decorative elements (rhinestones, beads, PAETIN) erase in special covers.
