During the operation of the washing machine with it can happen anything. If you find any troubleshooting of the device, you have two ways: contact your master repairman or try to eliminate the malfunction yourself. In the first case, you trust your faithful assistant to the housework of your business, but at the same time parting with several thousand rubles. In the second - you try to solve the problem with minimal losses for the family budget, but risk inextental actions to damage the complex mechanism.
What way to go, choose only to you. Those who decided to cope with their own will help our instructions on the disassembly of the washing machine and the extraction of the drum. This information is relevant for household appliances LG, Indesit, Bosch, Ardo, Electrolux, Candy, Zanussi, Whirpool, Hansa and other popular manufacturers.
Required tools
Before proceeding with work, make sure that you have all the necessary tools and materials at your hand.
You may need:
- a set of screwdrivers, including a cross and standard slot;
- Set of stars and hexagons;
- screwdriver;
- a hammer;
- pliers and pliers;
- set of end heads with a ratchet;
- Metal hacksaw.
It is not necessary for you to use all the above equipment - the complexity of work depends on the model of the washing machine. Some units disassemble very easily, and in order to remove the drum from others, you will have to work hard.
For washing machines with different types of loading, the procedure for disconnecting the drum can differ significantly. Consider a sequence of actions for appliances with front and vertical loading. Remember that for any model of the washer working on the removal of the drum should begin with the disconnection of the unit from the electrical network and disconnecting the hoses of the dialing and draining water.
Article on the topic: Hood for boiler
Front loading machine
Remove the Buck
- Armed with a screwdriver, remove the top and bottom panel of the washing machine.
- We unscrew the fasteners that fix the feeder of the washing powder and the control unit.
- Observing caution, disconnect these items.
- Do not forget to photograph each stage of work, to then collect everything in the reverse order without errors.
- Now remove the rubber cuff with the front panel, which seals the hatch door. To do this weaken the clamp, which is fixed with a small metal spring or plastic clamp.
- By freeing the front panel from the seal, remove it. To do this, unscrew the bolts in the upper and bottom of the machine.
- Now we take the front panel with both hands and disconnect it by pulling forward and up.
- The next step is the release of the drum from the wires connecting it with other elements of the washing machine. Disconnect the wires of the heater, pump, valves, as well as various nozzles.
- The liberated wires are assigned to the side and carefully fix that they do not get confused and did not interfere.
- To make it easier to pull the tank, remove the counterweight. They are in the upper and lower parts.
- Next comes a turn of shock absorbers and springs that hold the tank. Remove them alternately.
- Finally, carefully pull out the tank and disconnect the engine from it.
Visually, the process of removing the tank, see the next video.
Remove the drum
Most of the work behind, and we can only remove the drum from the tank. Further actions depend on the variety of tank. It can be collapsible or not collapsible.
If the tank is collapsible, simply we connect the brackets connecting two halves of the tank.
If the tank is not collapsible, you will have to cut it. It is for this that we need a hacksaw, which we stored at the beginning of work. The place of cut to determine is easy - you need to navigate on the welded seam. The puck sawdwood can be "reanimated" by connecting the halves with brackets or bolts (and be sure to treat the connections to the sealant).
Article on the topic: Capital or cosmetic repair of the facade
Now you need to pull the drum from the broken. First, just remove the front of the tank. Then disconnect the pulley. It is attached on one bolt, which you want to unscrew, and then spin back. After that, take the hammer and carefully beat them on the shaft. After several shots, the drum, as a rule, can be knocked out from the tank.
Vertical loading machine
- Using a screwdriver, we unscrew the fasteners fixing the rear panel of the washing machine, and remove it.
- We shift the sidebar to the side, then remove it.
- Carefully disconnect the wires, pre-photographed the position of each of them.
- We unscrew the screw that holds the shaft. Close the door of the loading hatch and carefully pull out the tank.
- Then disconnect the two parts of the tank and remove the drum (in the same way as for models with front load).
How to remove the bearing from the drum?
Most often, we have to remove the drum of the washing machine in order to diagnose and eliminate any malfunction. One of the most common breakdowns is wear bearing. To replace this item, you will need to disassemble the washer and remove the tank.
Pulling the tank from the washing machine and disassemble it into two parts, as described in the instructions above, you need to clean the drum. Remove the accumulated pollution and the foreign objects that fell inside. Then choose the bearing with a girlfriend tool, trying not to damage the nest. In addition to the bearing, we remove and wear the glands - we will also change these details to new ones. The mounting place of the bearing is processed by lithol, then put new glands and bearing. To secure the bearing, we need a hammer or a flood.
Remove the rubber band
In order to remove and replace the sealing rubber cuff on the loading hatch, you do not need to disassemble the washing machine and pull out the drum.
- To begin with, you need to remove the clamp, which fixes the outer part of the cuff. If the clamp is plastic, it is attached with the help of latches, and if metallic - with a springs.
- After removing the first clamp, carefully disconnect the second, internal. Place his fixation marker.
- Pull the cuff - first remove the upper part, then the bottom.
- We clean the edge of the tank, on which the cuff was installed, from dirt and processed by it soapy water.
- Putting on the edge a new cuff, moving in a circle. After that, we return both clamps into place.
Article on the topic: Tapestry seam in an embroidery cross: Fabric of smooth, large sizes, Lever and Schemes for free, Riolis