Fitting for toilet with lower eyelvering

The toilet bowl with the lower eyeliner is a container, below which the hose with water enters. In this container and stored water to the drain procedure. The tank is located on top of the tank. In modern toilet bowls on the lid there is a flush button, but in some models it is mounted on the side if the tank is located high above the bowl. The lower lining is considered the most imperceptible and attractive option for the toilet. However, it is quite difficult to create. To do this, it first connects the tank to the water supply, and only after that you can fix the tank to the wall or the base of the toilet.

Used in the toilet bowls with lower eyeliner divide into two categories:

• Shut-off;
• Drain.

Views

Shovel

The design of this reinforcement includes:

• Float;
• Guide;
• Traction;
• Glass;
• Membrane valve.

This toilet bowl works on the following scheme:

• When the tank is empty after plum, the float goes down the guide;
• Next, the thrust has an effort on the valve, thereby opening it;
• From the water supply system, water fills the tank of the tank;
• The float chamber at the same time begins to move to a limited level of level;
• The valve overlaps, the water supply is stopped.

Drain

Drain fittings is a water drain system. In the tank, it is attached with the help of a cape nut, preferably made of plastic. To seal the junction, the seals are put on the trigger pipe fittings. And to do it before assessing the reorganization itself. Also there is a gasket between the bowl and the tank, which allows you to make a mixer and prevent water flow to the floor. The form of the gasket used directly depends on the model of the acquired toilet.

Tasks of the drain system:

• Provide drainage of water when pressed by the corresponding button;
• Ensure emergency reset (provided for a special chute).

Article on the topic: What can replace tile in the bathroom - Alternative to Tile

Constructive features

To remove the descent mechanism from the models with the upper layout of the button, it needs to be scrolled counterclockwise, after which the button is easily removed, like the entire lid.

Not rare cases of toilet bowls with lower eyeliner, where there are two buttons. This is done in order to save water during plum. A small button merges some water, big - two times more.

The internal content of the tank is different. Sometimes straight plums are used, in which water from the container enters the bowl. Other designs have a reverse washing, where the direction of water movement changes, which adds noise.

Benefits

1. Possess an attractive appearance, since the pipes are hidden from the eye of the user.
2. The toilet itself with this eyeliner is often performed in the original form and with an unusual design.
3. The system practically does not create noise, there are no irritating many sounds of flowing water.
4. The most practical option, since it is characterized by high reliability and less frequently need repair and maintenance.

disadvantages

1. Mounting complexity.
2. Necessity In some cases, completely dismantle the system to repair the drain tank.
3. Despite the rare cases of failure, if it happens, replacing a separate design element is difficult. It is better to immediately change the node completely.
4. Such toilets are focused mainly on America and Europe, because problems may arise due to unique adapters, unusual for our clutch region. Therefore, the toilet and all components for the connection are better to buy immediately in the same store.

Installation

Mounting is quite possible. However, it should be noted that this process is characterized by increased complexity, if compared with the toilet bowls with side lining, for example.

One way or another, the sequence of your actions should be as follows:

1. Each product has its own community, where the detailed installation instructions are specified. Check out her.
2. Carefully examine everything that went bundled with the toilet. As a rule, manufacturers provide the necessary fasteners and connecting elements.
3. Install the lower part of the toilet, fixing it in the right place and position. Make sure that the lengths of the nozzles are enough, and the eyeliner will reach their places.
4. Now the tank is mounted. Just at this stage, it is necessary to install an inner structure.
5. As practice is shown, the first bulk valve is mounted, and when docking the tank. To do this, you will need sealed rubber gaskets and adapters.
6. In some cases, at the same time with the filling valve, the input valve is mounted. But it depends directly from the selected model of the toilet.
7. Collect the remaining elements will not be difficult if there is an instruction on hand. Units are often unique in their design, because we cannot give general assembly tips.
8. All structural elements are made exclusively manually, the tool is not required here. At the same time, make enough effort so that the compounds are durable.

Article on the topic: Crafts from stones and sea pebbles (40 photos)

Frequent problems and their elimination

1. Over time or during an improper installation, leaks may occur from the outside of the plum nozzle, during washed or from the tank itself. Such a phenomenon indicates only one thing - the gasket is leaking. To correct the situation, slightly tighten the plastic nut connecting the tank and the nozzle. If after that it did not stop the flow, then overlap the water, unscrew the nut and pull the pipe down. Pull, the gasket should appear soon. Remove it, and on the tip of the nozzle, do about 10 windings of the fum-ribbon. Put the item to the original position and tighten the entire nut.
2. Water does not merge. Check the fluid level inside the tank. According to the rules, it must be the top level. If it is small, sometimes it is enough to adjust the angle of the float lever. A screw valve from plastic spins for adjustment. Here you will need a screwdriver. In brass products, the lever is extensible manually or weakened the nut on which the float is mounted, and shifts up.
3. Drain goes jerks. Inspect the fastener of the drain system lever. It is probably sinking, and then the lifting rod will not raise vertically. To solve the problem, simply clamp the bolt and adjust the lever in the desired position.
4. Fabulous lever failed. There are special universal elements for replacement, which are not a problem today. In some cases, substitutes have to shorten. The main thing is the lack of clips between it and the siphon block.
5. Lime bloom. You can get rid of it with appliant means - lemon acid and water. From the drain siphon you need to remove water, apply a paste from the specified ingredients. We'll have to leave it for the night. Such a mixture is superbly coping with a raid.