In the course of operation, each subject of the interior is wears, gradually acquiring more and more damage. And the bath is no exception. Over time, its coating is wearing, which affects not only the appearance, but also on the properties of this product. However, not only time, but also various other circumstances, for example, material and conditions of operation affect the condition of the bath.
Many people have repeatedly wondered how to bring an old bath to a primordial look. You can simply replace the product, but in this case you will have to face a lot of possible difficulties. Quite often, when replacing the bathroom, it is necessary to replace the bathroom and finishes completely, and this will definitely apply large financial costs.
To avoid difficulties today, there are several modern technologies for renewing the bathroom coverage. The most commonly used insert technology "Bathroom" and applying a new enamel coating. To apply a new coating on the bathroom, a liquid acrylic is used, which The technology was named "Restoration of bathroom with liquid acrylic". In order to restore the bathroom of this technology, you will need acrylic enamel.
Benefits of material
Compared with other materials used to restore the bathroom coating, acrylic has a number of advantages. Consider them in more detail.
- High exposures of wear resistance and durability. Acrylic bathing can be in operation until fifteen years old. Analogs of this coating can not serve for so long.
- Almost complete absence of smell . Liquid acrylic almost does not possess the smell. Such a property of this coating allows you to work on the restoration of the bathroom without the use of funds protecting the respiratory tract.
- Uniform mixing of the substance. During mixing the base and hardener, which are components of the liquid acrylic parts, it turns out a homogeneous mass, which avoids an uneven surface coating, which happens when using analogs of liquid acrylic.
- Lack of spots during use. The process of operation of the bathroom after the restoration will not be accompanied by the appearance of spots on the surface.
- High uniform material. This property avoids air and the appearance of bubbles in the enamel has not yet hardened until the end of the enamel. Due to this, the amount of toolkit used during restoration is reduced, and a uniform glossy coating is also guaranteed.
- Short time drying . On average, the liquid acrylic solidifies for thirty-six hours, providing a uniform smooth coating. When using analogs with a smaller drying time, the defective sections of the coating are possible.
Article on the topic: Boxing box for storing umbrellas, ladies' trifles and not only!
Restoration technology
When using liquid acrylic for restoration of bath coating, high time costs, forces and means are not required. To date, the bulk bathroom with the use of liquid acrylic is sufficiently inexpensive and efficient technology to resume the qualitative characteristics of the bath surface.
Self-inflicting enamel - economical, when it is used, a large amount of source material is not spent. In addition, the resulting coating exhibits greater resistance to chemically active substances that can aggressively affect the renewed surface.
The technology is that the material is applied with a bulk way after preliminary preparation of the bath surface. The process can be performed independently by spending the minimum of money and time than the popularity of this technology is due.
Stages of work during self-influential restoration
The restoration of the bath in bulk means using liquid acrylic can be carried out independently. However, for this it is necessary to observe a clear sequence of stages.
Required tools for work:
- respirator
- putty knife
- sponge
- Gloves
- Drill or Bulgarian with an emery nozzle.
Stages of work:
- Preparation of the surface. Before applying acrylic, it is necessary to prepare the source surface. To do this, first remove the old coating. Apply for this, abrasive stones, drill or Bulgarian with a sandpaper nozzle. After the old coating is completely removed, and the remaining particles are washed off with warm water, the surface must be degreased. The preparation of hot water in the bathroom is completed by about 10 minutes.
- Preparation acrylic. The liquid acrylic used in the restoration of the bath is prepared by mixing the base and hardener, which are supplied complete. In order to make it ready for use, the solution, it is necessary to thoroughly mix the components according to the instructions, stirring them up to the stage of the homogeneous mass of milk-white color.
- Applying a mixture. When the solution is ready for use, it must be gradually pouring into the bathroom, covering the entire surface. At the same time, it is necessary to start with the upper parts of the bath, passing around the perimeter. Special attention should be paid to the bottom - it should be clearly formed before the material hardens. The adjustment of the surface is carried out with the help of a rubber spatula, and excess acrylic, if any, can be washed into the drain hole.
Article on the topic: Choose a mirror for the bathroom: distinctive features
See the following videos, where you will see in detail the entire coating process with liquid acrylic.
How to cook the mixture?
As mentioned above, a mixture for coating a bath is obtained by mixing two components. Initially, it is necessary to thoroughly stir the basis for which the acrylic semi-finished product is, and after gradually add the second component to it - a hardener, while thoroughly stirring to obtain a homogeneous mass to ensure uniform coating of the bathroom surface.
Please note that the poorly mixed solution can not only cover the surface with an inhomogeneous layer, but also to have a negative impact on the performance of the acrylic bathing of the bath.
If it is necessary to make a mixture of a certain color, after receiving the homogeneous mass of the liquid acrylic, the kel is added. The amount of the flaker depends on how saturated shade you want to get as a result of the coating.
When the mixture is obtained, it must be withstanding a certain time, which depends on the temperature in the bathroom. For example, if the temperature in the room exceeds 30 degrees, the mixture can be applied after five to seven minutes, and at a temperature of 20 degrees, the exposure time is 15-20 minutes. After exposure you can apply a mixture on the prepared surface of the bathroom.
Time and Material Consumption
Materials for restoration of the bathroom are spent in proportional dependence on the size of the bathroom. For example, a bathroom of a month and a half last meter requires 3.5 kg of materials, and for the restoration of a bath long 1.7 meters, 4 kilograms of acrylic will be required.
On average, this procedure is required from two to four hours, taking into account the preliminary preparation of the surface. The process of applying liquid acrylic on the bathroom is not more than one hour, the rest of the time will be occupied by preparatory procedures (cleaning and degreasing the bath).
Compliance with security measures
During the restoration of the bathroom, security measures must be observed. For example, during the preparation of the surface to the restoration, the respiratory tract should be protected through the use of the respirator and gloves. When applying a mixture on the bathroom you can also use the respirator.Article on the topic: How to choose the right Tulle to the curtains in the room: experts advise
Tips for restoration of baths in bulk technology
When using a liquid acrylic for restoration of the bathroom, take care that the working surface is cleaned, degreased and dried. This applies not only to the bath itself, but also tiles or other surfaces, which can be between the bathroom and the wall.
In addition, if there is a need to cover the mixture and part of the wall, secure the surface as a horizontal position. To remove the elevated pieces of cement, you can use a new dry sponge or a piece of foam.
When drying the surface, it is best to use a typical hairdryer, not a construction. It will be safer for you and provide the best conditions for the restoration. It is also recommended to felt the floor around the bathroom with newspapers or PVC glue, as it is possible to contaminate the surface of the floor during operation. The vertical parts of the walls in contact with the surface are protected from contamination - painting scotch.
It is not recommended to dilute the mixture for enamelling by other chemicals, for example, the solvent-obtained layer will be fine and poorly, which will reduce the operational characteristics of the obtained bathroom coating.