Floor grinding is a process that can be performed by its own ruewood floors is practical, aesthetically and environmentally safe. The grinding of the wooden floor is a mandatory preparatory work, after which the coating is already toned, cover the protective composition and exploit. Most appeals to professionals, but you can alternate the boards with your own hands.
Repairman itself: Wooden grinding independently
Those who decided to independently grind the wooden floor or parquet, will have to get a certain set of words, not to do with pricks. Alternatively, you can rent the necessary equipment.
Master will be needed:
- Cycle;
- Ribbon and manual grinding machines;
- Sandpaper having different density and linden (special paper for grinders on velcro);
- Varnish;
- Roller or brush (to apply lacquer).
Floor grinding process with their own hands
Separately, optionally, you can purchase a tint, if there is a desire to darken the coating, as well as putty, if the semi is visible cracks, from which it is necessary to get rid of.
Manual grinding machine will be needed to work in hard-to-reach places. Get tissue grinding - expensive pleasure, so it is best to take it for rent from a firm providing services for polluting floors.
The labeling of sandpaper can be viewed on the back of the sheet. For example, paper with the P24 label is needed for the most uneven floors or for coating, painted in several layers of paint. P100 or P80 are used to remove the pile when polishing is at the final stage.
How to polish the boards: tools and equipment for work
For each type of floor covering, its grinding equipment is provided.For example, when you need to polish the wooden floor laid on the lags, you will need drum equipment. It is rather heavy, not suitable for fine flooring.
Article on the topic: Curtains in the living room combined with the kitchen: how to choose and make a right
For each type of floor covering there is its grinding equipment
There are other types of equipment:
- FlatSheliform (for working with parquet). It is divided into two subspecies - to work with a large area and manual.
- Ribbon (used for pre-cycle of the sex surface);
- Vibration (to work with a conventional wooden floor).
The usual Bulgarian with a petal circle saves when it is expensive to get expensive equipment. It is also suitable for working with parquet. The work will take longer, but as a result, the coating will look no worse.
Grinding floor from a headboard: work stages
If the purchased centering floor must be covered with a layer of oil and varnish, it will take the grinding of the boards before these works. Also sanding the boards will have to be able to inhale the second life in the old flooring. Such a procedure is called cyclo.
Coloring board floor
Cyclishing - Removal of the old top layer of varnish and wood.
After cycling, the board is again treated with antiseptic means.
Before work: surface preparation and precautions
To begin with, take care of safety. It makes sense in special equipment.
Before starting work, the premises must be freed from furniture, textiles and other decor elements.
Namely:
- Respirator;
- Protective glasses;
- Beroshi or headphones;
- Gloves.
Before starting work, you need to free the room from furniture, textiles and other decor elements. Plinths are also removed. Boards must be clean, rotten replaced with new ones. With the help of a construction vacuum cleaner, the floor is cleared.
If work is carried out in one of the rooms, you should drill the interior door with a wet rag so that the dust does not penetrate into other parts of the house, even in the case when a professional parquet-liquery machine is used equipped with a dust bag.
First stage: floor cycle
First of all, you need a refueling of the machine with emery paper. In the drum of grinders insert a coarser-grained sheet with marking P40. By turning on the equipment, it is slightly tilted to yourself so that the abrasive does not spoil the boards. Ground the floor starting from the corner of the room, move diagonally into the opposite corner. With each turn of the car you need to lift a slightly unit. The new row should be on the previous 10 cm.
Article on the topic: Warm floor under carpet: heated carpet and electric heater, do-it-yourself rug infrared
Flooring - simple and efficient process carried out by grinding machine
If there is no experience with the grinding machine, so as not to make a hole on the floor or do not spoil the tree, it is best to pre-train on plywood sheets.
Corners of the room, places under batteries and stairs can be plastered by hand cycles, a grinder or emery timber. From wood dust after each stage, they get rid of a vacuum cleaner.
Second Stage: Grinding
Start the next stage follows from replacing sandpaper on the medium-trimmed with the R60 marking. Move with the unit is necessary in the direction of the fiber of wood, that is, now you need to move across the room.
Paul grinding is carried out with the help of a special car, after preliminary surface preparation
The grinding machine consumes a large amount of electricity (up to 2.5 kW / hour). Wiring and automata must be prepared for such a load.
Then the surface is again cleared of dust. In the process, the abrasive will often be hung, it should be replaced in a timely manner. Equipment engine is turned on or off only in motion, otherwise traces will remain on the surface. It is impossible to stop with the included machine.
Tanning Stage: Finishing Grinding
Paper in the drum is replaced by finely cell (marking P80 or P100). The movement also starts from the corner diagonally, along and across the room. After grinding the adhesive floor (non-tipped board), the surface is putty.
The finish grinding process
The finished coating is purified from dust and garbage, and then covered with varnish. The first layer can be applied on the same day. Usually, 2-3 layers of varnish are applied to the wooden coating or parquet. The polished surface looks fresh and updated.
Do it yourself repair: how to polish the tree manually
You can update the appearance of the wooden floor with your own hands without using expensive equipment.
Need to work:
- Sandpaper;
- Grinding skin;
- Pair of hands, well, or legs (who is used to grind);
- Cycle. This is not cheap tool, so it is necessary to ensure that it does not fail, to the cutting edge in a timely manner.
Article on the topic: Decorative plasterboard - for spectacular decoration
Technology is simple. The surface is exempt from the interior items, the floor plinths are dismantled. The protective coating of the floor is delivered.
You can polish the tree manually using sandpaper
The floor must be inspected for the presence of protruding self-tapping screws or nails. If any, they need to be dried in wood. To update the old parquet, you will need to check the dies. You need to make sure that they are properly screwed to the base.
After grinding with a rough abrasive, cracks on boards or parquet dies. And then then proceed to the finishing floor processing.
Grinding machine for wooden floor: Tips for choosing
Universal equipment for grinding do not exist. Estimate the advantages and disadvantages of each type of grinding machine can only be working with the unit.
Depending on the characteristics of the process, the main types of this electrical equipment can be distinguished.
Grinding machines for wooden floor can be several species
Grinders are there:
- Tapes . They are used for grinding of large flat surfaces. Suitable for working with wood, plastic and metals. The process is similar to the movement of the tank or tractor caterpillars. From the disadvantages allocate the impossibility of treating the corners.
- Vibrhlifovalny . It differs from the previous car fastener of the abrasive (to the sole of the unit). The principle of operation is based on vibration.
- Eccentric . Machines are similar to vibrhliform, but differ in abrasive nozzles (not rectangular, and round). The platform is not only vibrating, but also spins around its axis.
- Globlikhlifoval . Bulgarian is capable of sanding any surface as flat, the same curvilinear. However, it is difficult to work with the floor.
Grinding wooden floor with their own hands (video)
Whatever kind of grinding machine you have chosen, the main advantage of the equipment will be a fixed power button. So the master will not need to constantly press the button, grinding the surface. From other advantages for which the unit should be selected. It is worth noting a large power with a small weight, smooth start of the machine, the presence of several speeds.