Many motorists have their own premises in which they put their cars, notes most often except the observation pit there are no other devices. But in your power to turn the place to store the car into a full-fledged working area, it is only worth attaching a little effort and smelting.
Any good owner knows that its own workbench is a very necessary thing in the farm.
Therefore, after examining the information carefully, we offer to your attention step-by-step instructions, with which you can make the workbench in the garage with your own hands.
First of all, make a list of the necessary building materials (the pine wood is perfect), tools and thoroughly work the drawing of the future machine.
Purchase the types of suitable sizes, it is best if there are two of them - one you mounted on the right side, and wake them up when processing long parts, and the second, place on the left side, for the processing of short parts and edges.
In construction stores you can find both imported and domestic vice. What is the latter much cheaper, but not worse.
The next step is to form a countertop, although it is necessary to dig in your reserves, and you may find it ready in your bins.
We are determined with the location of the workbench, well, if it is the most illuminated place in your garage or shed. To do this, carefully calculate the size of the future machine, in order to avoid all sorts of alterations.
Also, it should be remembered that the workbench is better to fix it stationary, so during the processing of materials it will not move and work on it will be very convenient.
Making workbench do it yourself
We proceed to assembling an exposure. I am fixed to the wall of the bar, which will perform the role of carrier. The second bar, with a similar function, fixes on racks, in advance to the wall. During all works, we use the level to control the planes.
Article on the topic: Cement-sand tie density: Specific weight
To the surface of the floor, dripping vehicles serving the framework of an exposure framework.
The substole is folded from the bonding of the bauses in Polterev. It will not take much time if you are used in drill and jigsaw. For the attachment of the podstoley to the legs using self-tapping screws.
Optimally, when calculating the Podstol parameters to leave the stock into several centimeters so that it can, as if to suit the table top. In this case, you can easily remove the construction trash from the tool.
Cut out the exposure, corresponding to the size of the legs, fastened under the basis of an exposure and connect the axial bars on top of the screws. The same operations are made at the bottom of only the defects between the legs.
When forming grooves, make sure that they have the shape of the rectangle. Cover the finished design with a varnish, so it will keep an attractive appearance for a long time.
After you mounted an exposure, proceed to the installation of joineric vice. This is quite a painstaking work that is not tolerant.
We apply vice to the back side of the countertops, and marks the place of their future dislocation. Make sure that their sponges are either at the same level with the worktop, or a little lower.
If the table top length does not allow you to use the gasket. Also remember that the vice should not be too close to the edge of the table top, otherwise you will break its edges.
Remove the place of fastening bolts. It is desirable that the screws have counted heads.
However, if there are no such available, you will fit the usual. And then you will have to shoot the pits under the heads of the bolts, in order to achieve a position slightly lower than the table top. Thoroughly, using bolts, attach vice to the tabletop.
Using 4 screws, fasten the worktop to the podstol. At the end of this stage, we are already ready the main workbench.
Next go to improve the qualities of the table top. It can be additionally used by boards or plywood, as well as coat with an organity with small screws. Such actions will make the surface smoother and easily changeable if necessary.
Article on the topic: Protective Blinds: What are you how to install and manage?
Provide on your workbench stops for vice, with their help you can handle large details. The easiest way to purchase them in specialized stores, although it is worth noting that their price is pretty rather big.
You can also improve your workbench, additionally supplying it with various shelves and drawers, in which it will be convenient to store billets and work tools.
Thus, equipping your garage with this extremely necessary machine, you can turn it into a very convenient workplace, and still save money by making your hand workstak.
Take a look at our construction forum if you have any questions. Our specialists will prompt how to make a workplace in the garage as convenient as possible.