The floor of the OSB-slabs can be found quite frequent to lay the OSB laying on the wooden floor or wall, it does not need complex highly professional installation, but accurate should be observed, as it is important not to miss, not a single point in the laying technology.
How to cover the floor from OSB on lags and on concrete
Make the OSB flooring is not difficult, and you can use the simplest panel. To make the floor to be more durable, it is worth choosing a cloth with grooves. The joints should be located directly on the lags, but if they are too large, it is better to install an additional fastening element. To put the OSB panels and make the floor on the lags, you will need to first prepare the necessary inventory.Namely:
- Lobzik;
- Drill;
- Roulette;
- Self-tapping screw;
- Building level.
Between the bars should be a distance of no more than 40 cm, and in this case, the laying of sheets with a thickness of 1.5 cm is allowed. If the distance is greater, then the panels should be thicker. The distance between the boards make the same, and it is still important to put the plates correctly to stay a small gap. The lumens will be subsequently filled with the most ordinary mounting foam.
Make an OSB flooring with her own hands just enough
If additional thermal insulation is needed, you can use foam or the most common mineral wool.
It is possible to put the CAP cloth on a concrete screed, and for this it is necessary to follow the sequence of actions. The base is prepared. The floor should be thoroughly speaking, so that the dust causes the poor clutch and floor. Be sure to progress the surface of the concrete. As a solution, any primer can be used, even deep penetration, even normal. Next, you need to take a sheet, it can be done with your own hands. Be sure to take into account such a moment as leaving the technical gap of near the walls, which should be peeling 5 mm. This is required in order to eliminate the leaf intution by increasing their size, which occurs when the moisture is exposed. Direct installation is carried out by means of rubber-based and a clogged dowel. Before driving sheets to concrete floor, you need to put the insulation, and also make sure that the canvas are smooth and suitable for construction. Laying on the draft floor is not complicated, and it is possible to do everything yourself.
Article on the topic: How to properly sew the wall of plasterboard?
Benefits of Paul Panels
Such a building material like an OSB-stove has a mass gain, thanks to which many prefer to lay it on the floor. The material has such a high density that the canvas cannot bother rodents and harm its integrity. This finish is resistant to moisture.
Accordingly, select the panels for:
- Baths;
- Bathroom;
- And the like wet premises.
The canvas have an excellent press, and therefore, even small trimming will not crumble. The product has excellent resistance to biological factors. The canvas is completely environmentally friendly, since the manufacturer uses natural wooden chips.
OSB-stove has a weight gain
Conduct installation at least to concrete, at least another reason is not difficult and professional preparation will not be required.
The cost of the material is not too big, and one element has enough impressive dimensions, which means it can close the large area. OSB has a great level of reliability, which allows you to make the most qualitatively to carry out not only the finish, but also the construction. Due to good wear resistance, it is possible to use the canvas for a long time and not worry about the formation of defects, since the material does not succumb. OSB is hard to bend, easy to cut and replace the new one.
OSB thickness and composition
The characteristic of the material means a lot, but when choosing OSB sheets, you need to pay attention to such a criterion as the parameters and firm manufacturer. Creating a finishing floor, or possibly, it will be a substrate for laminate on the balcony, you must always adhere to recommendations from the selection of finishes and then, it will fully justify the expectations.
Masters with extensive experience with such canvases prefer to use the European and Canadian panels.
Choosing OSB plates, consider their specifications and firm manufacturer
Choosing thickness is carried out by:
- To which the coating will be laid panel;
- Budget;
- Operational properties.
As for the sizes, there is one single standard, and it is 2.44x1.22 m. Thickness of dimensions does not affect, but on the quality of the finish, yes. If you need to fix small pieces of OSB, it is possible to cut the cloth at home, which will not deliver much difficulty and problems.
Article on the topic: Decorative plates on the wall do it yourself
Budget furniture from OSB do it yourself
OSB plates are perfectly suitable as the decor of the kitchen, for example, for the plating apron or the creation of original shelves. Very unusually look at the openwork locker or bookshelf in the office.
The use of OSB panels is very diverse, as the board can be installed as the partition between the rooms, and also to be used:
- For the arrangement of the roof in a private house;
- To finish the stairs to the second floor;
- As a sheat;
- As a canvas to close the warm floor;
- For the manufacture of furniture with your own hands.
With the help of OSB-boards, you can make the furniture with your own hands.
Due to the fact that the plates are solid and they will not give a skew, they make massive cabinets. Among additional benefits should be noted the presence of a decorative structure. Furniture is made simply, but it looks very unusual, and sometimes it does not even need additional finish.
If the furniture from the OSB glue the original pictures by creating the style of Provence, you can achieve an excellent result and create your own original interior.
Weight options, but it all depends on the preferences and capabilities. If you wish, you can construct a whole children's town inside the house, but you must first get acquainted with what kind of screws will be used to hold the mount.
Proper laying of OSB on a wooden floor
Over time, its aesthetics loses any coating and therefore, to close the old milking floor, you need to lay the OSB plate, and it is better if the board is moisture-resistant. There were still such premises in which there is not a linoleum on the floor, but a boardy floor.
Many rushed such a coating, as it:
- Durable;
- Wear-resistant;
- Durable.
Before laying OSB-stoves, it is necessary to prepare the base of the floor
The principle of laying the floor is thus not complicated. The base is prepared. It is necessary to trace so that there are no sticking nails. If for the period of operation of the board not just deformed, but they became not even, then before the fastening is carried out, it is necessary to align. For this, the plans are used.
When laying out of OSB outline, you must not forget about the seams to displace the canvas.
The mount is carried out by self-draws, the length of which is 4 cm. The fastener is installed with a distance from each other at 30 cm. Hats must be recessed inside the coating. After completing the work, you need to stall the joints of the canvas.
What ways to carry out the installation of OSB on the walls
Do not confuse the OSB panels with such a material like plywood, the front side of which is unlikely to surprise someone. It is worth noting that it is also necessary to correctly pronounce the name of this web.
Article on the topic: How is the wooden window frame done with their own hands
Some pronounce the incorrect interpretation of OSB in the form:
- Yusb;
- USB;
- OSP;
- Wizby;
- Yizby;
- Wesby;
- HSB.
This is required in order to cover the floor or walls, it is the OSB panel, as an incredible number of building and finishing materials is available on sale, and it is not difficult to confuse them by name. The laminated OSB panel on the bulk floor or concrete is placed using such compositions as mastic or glue.
To secure the OSB plate on the wall, you need a doom, installing to the building frame
To glue the cloths among themselves, that is, a concrete and a board, you need a lot of composition, but how much you need, it is calculated depending on the situation, since more solution is translated on a porous coating.
To secure the product on the wall, you need a doom installed to the framework of the building. The installation of the plates is carried out by two-link spiral nails at 51 mm or rings in 4.5-7.5 cm. Drive is carried out every 30 cm in the backups in the intervals. Where the plates are connected, you need to drive the nails after 15 cm. In addition, you need to take care of leaving the dialing gaps so that the installation was as correct as possible. Between the edge of the slab, located at the top and the beam of the trimmed type, the space is 1 cm. Between the edge of the plate located below, and the foundation also leaves 1 cm. Between the canvases that do not have grooves must be 0.3 cm.
In some cases, the decoration of walls, covered by the panels of the OSB, is not in the future, as there is a very unusual room with such a finish. The most common way to decorate the canvas can be called shtclosure, as it is not only an finishing finish, but also additional sealing of slots and joints. The qualitatively done shtpocking allows you to get an ideally beautiful room. If necessary, putty can be painted, cover with wallpaper or any other finishing materials.
Floors from OSB do it yourself (video)
In order for repair work or the construction of furniture from the OSB panels, competently and fully justified the expectations, as well as the costs of forces, tools and time, it is necessary to carry out all processes according to the previously made project and only from quality material.