How to make joe-doors with your own hands? Now it has become very popular to install sliding jiggle doors. They help to create a spectacular interior of the room and allow you to save the place that the door canvases occupied when they open.
Types of interroom doors.
The design of the sliding doors does not provide for the settings of the thresholds. They are easy to open and close. They are suitable for any interior of the room.
However, they do not provide complete sound insulation of the room. Therefore, they are usually installed in the living room, in the kitchen, where noise insulation does not matter. The coupe can be with glazing or without it. They may have an upper or lower guide. Constructions may have a different number of sash.
Installation of coupling doors
Schemes of sliding doors.
You can mount the jiggle doors with your own hands. When installed, two methods are used. So, the sliding door can be mounted in the wall or wall.
If a method was selected in the wall, then you need to prepare a niche of the necessary sizes.
Materials and tools:
- door leaf;
- fastening elements;
- Metal guide bar;
- videos;
- wooden bar cross section 50x50 mm;
- Coolband for top of the door frame;
- lateral platband;
- The rack to which the door should be adjacent in the closed position;
- self-tapping screw;
- Anchors;
- Finish nails;
- doorknobs;
- Good.
Coupling door device.
First of all, it is necessary to install the guide bar and fix it with self-reserves to the bruus. To do this, drill holes under the tapping screw in the metal bar. Holes should be placed at a distance of 20 cm from each other.
Then you need to perform a special groove at the bottom of the door canvase. It will move the guide roller. This groove is needed so that the lower part of the door does not move during the movement.
The grooves can be performed using a cutter or a feather on a tree. Carefully perform holes. Then with the help of the chisels are cleaned too much.
Article on the topic: How to clean the drum of the washing machine?
Then it is necessary to install the bar bar of the guide. It is installed in a strictly horizontal position. If during the installation to allow inaccuracy, then the canvas will be able to open when it is not necessary. Then install rollers in the guide. The bottom roller is fixed in the floor.
The roller under the top bar must be fixed strictly horizontally, otherwise the canvas will not be vertical.
After that, you need to install the product on the lower guide roller. Then the designs give a vertical position and fixed to the top rollers. In order for it does not go beyond the boundaries of the guide, you need to install limiters.
After that, the side of the box is mounted vertically boxed rack. It is installed and fixed to the wall using the corners. They are closed by good.
Scheme of fasteners of the coupling doors.
Then the platbands are installed on top and side of the opening and nail them with the help of finish nails.
Now you need to attach the handles. They are mounted after the final installation of the canvas.
In order for sliding doors to make each other more tightly, they need to stick dustproof brushes.
If the door-compartment will be mounted without the use of the threshold, then you do not need to perform the grooves, make rails. In this case, the design will be attached only from above. When installing such a design, it is not necessary to remove the floor covering.
Stages of performance
First, it is necessary to strictly perpendicular to fix metal strips. Then, with the help of a bolt and 4 nuts, it is necessary to attach the bearing.
Mechanisms for interroom sliding doors.
Then you need to try on the web for the way. Make the necessary marks. For these marks with the help of a perforator, he drill special holes for installing anchors.
Then you need to put a special gasket under the canvas, which will secure the product at the necessary height from the floor.
Next, you need to fix anchors. To one of them should be attached to a metal rail. Her bearings with the product attached to them.
Article on the topic: Instructions for installing plastic windows with their own hands
Raise the product. To rake fix the second anchor. After installing the rollers and fasteners, the design is fixed in its place. To do this, it is lifted and twisted the bolts into the brackets at the top of the product.
This work must be performed with an assistant, which will raise and keep the design while you twist the bolts.
Tools for mounting jiggle doors.
Then you need to check the horizontal product. If necessary, you should additionally twist the bolts.
Then installing platbands and sobers it is necessary to hide the slope of the opening. The roller mechanism needs to be hidden using a decorative plank. It is installed on top of the roller mechanism.
At the end of the installation of sliding doors, accessories and handles are attached to them. To ensure a quieter product, it is necessary to secure the rubber strip over the metal rail.
Installation of the door-compartment with a special niche in the wall will be more time-consuming. In this case, it is required to make a septum from plasterboard sheets. It will call it product.
If the door-compartment is mounted from the guide in the floor, then you need to perform a special groove at the base of the floor using a perforator.
If you follow this instruction, you can independently install sliding doors that will be durable and served for a very long time.