Water procedures occupy an important place in life. To hold them a shower cabin in the bathroom with their own hands. It can be installed both in the apartment and in a private house. Sometimes it is mounted even in the bath. It's nice to fulfill this work yourself and then be proud of it.
Shower Cabin Installation
You can make a shower cabin with your own hands. This requires material, tool and time. This device saves a place in the bathroom and gives the room a completely new appearance. Cab is on the pallet and without it. In the room with a small width, a device with a glass door without pallet is quite suitable.
Shower room
It looks pretty aesthetic, but it is difficult to collect it. The fact is that you need to remove the used water into the sewer. For this you need pipes located below the drain hole. In modern apartments, this is not always possible. Then you have to install the pallet.
- At the ceiling, waterproofing is necessarily performed for high-quality floor protection against moisture.
- Walls made of wood after treatment with waterproofing composition should be aligned with water-resistant plasterboard. From the usual facing it differs in green.
- Plastic pipes are paved, on which the liquid used will go into the sewage system.
- From above, everything is closed with tiles. It is placed with a slight inclination toward the drain hole. If possible, these works are performed inside the floor or directly at the base of the pallet. After the installation equipment, you can collect a shower cabin with your own hands.
Drain pallet
The pallet can be purchased in the store in the finished form. It does not need special knowledge and skills for its installation. The only difficulty that may occur during installation is the conservation of the podium. Make it easier from the brick. After installing the pallet, the joint is equipped with a special border. Such a tray of industrial manufacture has its advantages:
- Installation it is made easily and quickly;
- It is possible to adjust the height using a special design of the legs;
- The finishing border is included in the delivery kit;
- It can be mounted directly on a wooden base treated with hydraulic protection.
Article on the topic: Repair in the bathroom combined with toilet: photo instruction
Consumer reviews about work bath with a shower cabin are very good. But the cabin should be chosen carefully. It is necessary to check the mounting of the walls and doors, the coincidence of the pattern with the sewage pipes in the house. You can purchase not the entire cab, but only separate parts of it. Modern manufacturers give such an opportunity and offered to choose various designs from:
- polycarbonate;
- glass;
- fiberglass;
- Plastics.
To install the equipment, you need some tools:
- drill or perforator;
- screwdriver or screwdriver;
- Screws, spatulas;
- hammer, pliers;
- trowel, tiles;
- Capacity for the mixture, level,
- plumb, roulette, pencil.
For mounting the cabin, some materials will be needed:
- high quality cement;
- sand, brick;
- cranes, mixer;
- shower head;
- Plumbing pads;
- Pipes, couplings.
Sections are usually attached to the base so that they can be easily close and open. Installing them with your own hands, you can be completely confident as performing work.
Installation of different types of cabins
Installing the shower cabin with your own hands in the bathroom with a small square - the pleasure is quite expensive. But to make it with the acquisition of only some items will be released much cheaper, and they can serve a significantly longer period. A common material for the equipment of the place of adoption of the soul is a tile of ceramics. This material is not afraid of water, it is strong enough and reliable, its service life is measured by decades.
Ceramic Tile Shower Room
About the hygiene of this material and it is not worth talking. For the shower cabin, the walls of the bathroom are facing ceramics along with the floor. If there is a pallet, then it is also faced with tiles. Lined walls and will be the walls of the cockpit. It will only have to do a door or another partition.
Works should be started with floor-insulating floor throughout the bathroom area. To do this, clean the surfaces from old coatings to the concrete itself. A bitumen mastic or other modern material is applied to the concrete base. Any material must be applied at least 3 layers. The joints between the walls and the floor additionally sneak the ribbon from the phlizelin. The waterproofing layer is covered with a screed, which is made on the basis of cement. Screed can be additionally reinforced with a metal grid.
Article on the topic: Turquoise color in the interior
Next, you need to properly put the sewer pipes so that the water used without obstacles fell into the sewer system. Plum and pipes should be insulated with hermetic gasket. This place is better to arrange the wall opposite to the entrance. Cabin walls can be folded from glass blocks or sheets of durable glass. A homemade shower cabin ready. You can try it.
Some Installation Comments
- In the manufacture of the podium, brick, aerated concrete and other fillers are used. On top there is still a layer of a concrete screed with a slope toward the drain.
Pallet from bricks
- The trim of the cabin, lined with a cafeter, is reduced to the surface of the surface with a special grouting mixture. It is better to use a sanitary sealant as a grout. He is able to protect the room from moisture and fungus.
- The cockpit should be lighting. For this, the shower is equipped with lighting wiring. Putting it best to remove from water pipes with compliance with fire safety measures. Installing other devices may require consultation of specialists with experience and knowledge.
- For doors, a sheet of acrylic or glass is usually used. Acrylic doors are easily processed. All accessories are purchased in the store. Glass doors have high fragility and trauma. But there is a way to protect yourself with sticking glass of a special film, which does not allow glass to crumble on small fragments. You can make a door from a piece of tempered glass. But this method is worth a lot of money. Acrylic (before he was called plexiglass) allows you to make even bent doors. They are used in the sliding structures of shower cabins. They are made using a construction dryer, template and guides.
Glass shower
Conclusions on the topic
The bath is available in almost every apartment and some private houses. But the conditions of the bath are not always suitable for residents. I want to have your own full-fledged souls made with your own hands. Modern materials fully allow you to cope with this task. You can collect a shower room made of glass blocks and sheet glass, plastic and polycarbonate.
The color of the materials may be the most different. You can buy a full set in the store in the store and collect it, you can only buy part of the set, and the rest is made with your own hands. Such a cabin will cost much cheaper. The main thing is to make good waterproofing of the floor and walls.
Lighting should be in the cabin. To do this, the wires are stretched away from water pipes. Light bulbs better use special for shower cabins. They are made with vapor and moisture protection properties. You can also install a radio that is sold in specialized stores. The cabin is equipped with small things like a towel holder, a shelves for soap and detergents, mirrors.
Video instruction
Article on the topic: Drainage of the site do it yourself on clay soils: from groundwater, how to make yourself