The shower room is rightfully considered a rather complicated room, in terms of operation. Increased humidity, condensate, temperature differences - this is not a complete list of negative factors with which it will be necessary to face finishing materials. The tile in the bathroom can serve not one dozen years, however, what to do if she fell off? The answer to this question can only give a thorough analysis of the reasons for the separation of ceramic products. In addition, you need to know what to stick back!
Destruction of masonry
Initially, it should be understood why the tile falls off from the place of attachment? To do this, it is necessary to carefully analyze the reasons, since there may be quite a lot of them. There are basic types of defects on which you can establish a source of problems, as well as correct it. Types of problems arising:
- Violation of technology. Tile in the bathroom must be glued, observing all the requirements for the shower room, i.e. relatively high humidity, temperature conditions, as well as the level of adhesive layer.
Print tile
- Emptiness. If, after drying the glue or when laying the tile, air pockets were formed, then, most likely, the tile will disappear. This is happening when the void area reaches 1/10 of the part of the total area of contact of ceramics with a surface.
- Low quality glue. The poor-quality material in the form of adhesive composition increases the chances of the tile in the bathroom fall off with time.
- Bad adhesion. The poorly prepared surface or raw material does not interfere with a reliable adhesion of glue and a solution.
- Uneven surface. If the tile is laid out a short way, then due to irregularities there is deformation and loosening products.
- Excess glue. Many - does not mean good! If a too large amount of adhesive composition has been applied, then after a while it will begin to laugh or crumble.
- Lack of solution. A small amount of solution is also destroyed for mounting the tile with the surface of the wall. Therefore, you need to do so much mixture as needed by technology.
Lack of glue
- Strikes. If the bodies are constantly falling in the bathroom, then this is one of the reasons why the tile is falling down.
- Impact of moisture. If water penetrates ceramics in the bathroom, then it leads to the destruction of the fastening layer.
- Excessive load. If you have a heavy set in your shower, household appliances or plumbing, it is clear why the tile is moving.
- Temperature changes. Sharp modes change can adversely affect not only the fastening compositions, but also on the finishing materials.
- Old laying. Naturally, the outdated coating will be more susceptible to wear. Therefore, purchasing housing you need to immediately make repairs in the bathroom.
- Foundation mobility. If wood is added to the fastening solution or the base completely consists of wooden elements, then in conditions of high humidity, such a layer will begin to change its plane.
- Shopping housing. If the house is relatively new, then it is better to make repairs after some time. This is due to the fact that the final shrinkage of the building has not passed.
- Pollution. In the presence of a bold flooring or dust on the surface of the adhesive composition, the tile will begin to disappear independently.
Out of this situation
What should I do if the tile fell off? Glue the tile back! Of course, there are many conditions under which it is impossible, for example, a poor condition of ceramics. However, in most cases, the product is in a further type of operation. Therefore, to restore the interior, it is necessary to carefully clean the surface where the tile was attached. Then apply the adhesive composition and glue the product to the appropriate place.
Trimming the desired piece of tiles
This method is applicable only for tiles, which is in excellent condition, otherwise it is required to replace. Although it can occur in the absence of the desired item. Then you can play on the contrast or add bright colors to the overall drawing. To do this, purchase several ceramic products and put them instead of obsolete tiles, which will significantly refresh the bathroom.
If for some reason it is impossible to glue a tile or pick it off, then it is best to approach the solution to the problem of originally. Try creating a mosaic pattern, i.e. To colaw the ceramics, and then collect it and go into the old place, but already carefully popped. It is necessary to make such a procedure carefully to eliminate the possibility of a non-sustainable appearance.
To prevent rejection, it is necessary to establish the cause of the occurrence of a defect, after which it is possible to eliminate it. In practice, this is relatively simple, but you still have to try. For example, it is possible to determine voids by normal sound, catching up each element separately. Various irregularities are noticeable with a naked eye, as well as a crumbling solution. The detected defectory area will have to redo the conscience, otherwise there are no problems.
Raw materials for gluing
The tile of the tile is an unpleasant sight. However, the question than to stick back makes it makes thinking about more pragmatic things. The first idea that comes to mind is glue. But what to do, when the day off, holidays, no money or just laziness to go to the store? In this case, you can use proven methods that are available at home. Recommendations:
- Sealant. It is used for the smallest elements of the decor, but periodically ceramics will disappear again.
- The remnants of glue. The adhesive solution in the form of a powder is useful, as it is impossible, by the way. You can take the required amount and use to be appointed. Liquid solutions are not recommended to be applied, as they have been thick with time, losing their qualities.
Glue
- Homemade mixture. Usually for the preparation of this solution everything is at hand, i.e. Cement, water and sand. To enhance the characteristics, you can add a bit of PVA.
- Liquid Nails. This method is characterized by its speed, however, the durability is pretty suffering. The solution must be applied point and around the perimeter.
Liquid Nails
- Paint. In order to glue the tile, you can use even the usual paint, if there are no other means.
- Cement mix. Cement dough is not bad with the task in emergency conditions. It is wetted with water and applied to the opposite direction of the tile, after which it reliably holds the product.
Cement mix
- Mastic. The composition of casein and cement will be a good analogue of the classic tile glue.
- Bitumen or resin. At the expense of its properties, i.e. Viscosity and stickiness The mixture can be used to temporarily replace the adhesive composition.
Bituminous mastic
- Other options. Among other things, liquid glass is suitable for emergency cases, silicone-based adhesive and other mixtures with adhesive components.
Preparation and installation of coating
In order to restore the tile, it is necessary to carefully prepare an old surface. This is done under a new tile so that it lasts as long as possible. For which the remains of the facing coating are eliminated. Therefore, it is necessary to do everything carefully and carefully, and manually, so as not to damage the adjacent tile. Then you need to delete the old solution, if the glue is tight enough, then try to twist it.
Removal of old tile
When cracking and other irregularities are detected, the surface of a layer of minimum is 1 mm. The next step will be aimed at degreasing the base, as well as a thorough procession. These activities will improve adhesion, which, accordingly, will positively affect the operational properties of the coating. In addition, it is necessary to further impregnate the surface with anti-grapple compositions. Only after that proceed to restoring ceramic tiles.
Removal of old glue
Process:
- The glue to the product should be applied in such a way that the surface level is compared with the main coating in height.
- Then you need to strongly press the tile to the surface, knock on it so that the solution is evenly distributed under it.
- Surplus between the joints should be carefully removed and fix the distance between the cafeter of conventional matches or special plastic crosses.
- It is required to wait a little time to make the composition to dry, and then you need to lift the seams and clean the dirt from the surface of the ceramics.
Article on the topic: We put the floor from porcelain stoneware in the living room