What do not say, and engineering communications in the bathroom (pipes and sewage tubes) look, say straight, not quite aesthetic. Therefore, they are trying to hide them from the gaze, encouraging various elements. There are many masking methods, but one is the most common at present. This is a box of plasterboard for the bathroom.
The most amazing thing is that this design is simple, but at the same time exactly suitable for all requirements for elements of wet premises - and in moisture resistance, and by strength, and in appearance.
Banner in the bathroom
Important!
Such a box must be built in such a way that access to all systems for carrying out not only preventive work, but also with freelance situations.
Therefore, it is necessary to think over everything before starting to assemble work.
Montage Karcasa
The box for the bathroom of plasterboard suggests the presence of a frame that is made of metal profiles. If the box is decided to close the vertically standing pipes, usually located in the corner of the room, then the frame structure will be three profiles forming an equally chaired triangle in cross section.
Two of them will be attached to adjacent walls.
Marking and installation
Very important component in the framework of the carcass under drywall is to carry out accurate measurements. To do this, measure the distance from the wall to the outer edge of the pipe. It is for this size that the frameworks of the frame will be displayed. Do not forget to measure the length of the pipes themselves for precise profile trimming.
First of all, profiles are installed, which are attached to the walls of self-draws. To do this, you will need a perforator and screwdriver. But the third rack will have to fix pieces of profile to two first racks. Design in this case is solid and rigid.
Article on the topic: Risper for the floor Self-leveling: What better
How to determine the location of the intermediate rack? For this purpose, perpendiculars are carried out from the installation site of two wall profiles. Their intersection and there is a place for you.
By the way, it is possible to mount this rack:
- to the walls themselves using specially manufactured corners;
- To the willed racks with sliced profiles sliced.
In principle, both methods are a good solution. But most often still masters use the latter (photo from below). He is easier.
Attention!
In the event that engineering communications are located not in the corner of the room, you will have to arrange a full-fledged box consisting of three faces.
For this you have to install two separate racks from the wall, which will be attached to the cooler and interconnects. The price of such a solution increases.
Koroba frame
Articles on the topic:
Dancer from plasterboard
Pipe plasterboard
Conditioning box plasterboard
- First, the plasterboard panels are prepared, which are descripted precisely in the size of the rectangular faces of the box. Please note that bathrooms need to use moisture-resistant plasterboard.
- Secondly, the material sliced into pieces is fixed at the destination by self-proof.
- After all this is finished.
As you can see, nothing is difficult in this process. But it was the technology of installation of indiscriminate box for the bathroom. As mentioned above, it is necessary to provide in the design from the profile for drywall this device a small viewing hole, with which it would be easy to inspect and preventive work.
How can this be done not to disassemble the whole design in emergency situations? Of course, you can install on one of the loop racks that a small door is hung.
In order to make it, it will take a rectangular metallic frame from the profiles for drywall, covered with a piece of drywall. That is, there should be a full-fledged door. But it's hard enough to do it.
Article on the topic: Basic breakdowns of coffee machines
There is a way easier. A piece of plasterboard sheet is attached to an uncalatory frame, cut exactly in size. Subsequently, the box itself will be lined with ceramic tiles. But the tile on the front part of the box must be put in such a way that it does not overlap the place of attachment to profiles, that is, the screws.
Frame installation scheme
What is it necessary for? In the event of a freelance situation, the screws can be unscrewed and removed the front panel. But this option looks very beautiful, since the fasteners are visible.
Therefore, for decorating and for the legend of the presentable appearance, the gaps left under fasteners are decorated with special planks (and become invisible).
Horizontal boxes
In principle, this design is not much different from the vertical complexity and production. The only thing experts pay attention to are some additions.
For instance,
- The floor in the box should be slightly above the surface of the floor base of the room itself.
- In the box, it is necessary to leave a small hole at the bottom (even one is better). If it appears in the pipelines to flow, the water will first begin to leak through the hole data. This will help prevent troubles related to the flooding of the lower floor neighbors.
Full box
Useful advice
- In the event that the box is installed on the heating pipe, it is necessary to ensure the outflow of thermal energy through specially cut holes in the top panel.
- Before installing the plasterboard panels, it is necessary, without fail, to work out the chamorts of the edges to provide high-quality stake trim.
- Before laying the tile, the box is necessary to handle the primer.
Door on the box
Conclusion on the topic
Now you thoroughly understand how to make a box of plasterboard in the bathroom with your own hands. There is nothing difficult. And yet, many readers, for sure, have any questions that will help to answer the video posted on this page. Let it be for you a kind of instruction for use. Good repair!
Article on the topic: Cock stitch cross scheme: free download, sets of vintage, gold chicken, articles and mini charts with moon