Before carrying out facing works, all defects are removed on the walls. If for painting, shook wallpapers such a task becomes the main, the tile is put and without careful preparation. Of course, it will worsen the final result, but will save time and building materials.
Sometimes it is impossible to align the walls due to a limited area, since drywall and plaster "eat" the space significantly.
But at the same time, the method of laying the tiles to spend at least minimal work on wall leveling. Do it in one of the following ways:
- Plaster. Applied to problem areas. Additionally, work the wall with a thin layer of the mixture.
- Plasterboard. Used to eliminate serious depression. Here the frame is not needed, only a piece of material of the appropriate size is cut and glued onto the wall. The edges are slightly dropped, and the joke is shuttered with plaster.
- Bulgarian. It is used in the opposite problem - eliminate the convex sections, with its help, remove the influx of concrete. Take the fittings undesirable.
- Grid. Pre-fastened with nails or screws to the wall. Fixes glue and tiles on problem areas.
Such methods although they do not guarantee the perfect alignment of the walls, but improve their condition and allow you to produce better installation of the tile.
Ways alignment methods
Features of used materials and styling subtlety
First of all, when working with an uneven surface, the format of the tile itself is important. To make the differences as minimally noticeable, the optimal will be the selection of medium-sized tiles.
Regarding the adhesive solution, preference gives plastic purchased mixtures. The homemade sandy makeup shakes, if you apply too thick layer.
It is also recommended to use SVP. This device will facilitate the process of fitting the adjacent elements, the glue will be distributed more or less evenly and in the end it turns out a flat surface without drops.
Consider the method of laying tiles on an unprepared uneven wall. First, go through the surface level and mark the identified defects. Then minimize the drops found. Only after that the walls are soaked and proceed directly to the laying.
Article on the topic: Exterior and interior of the House in Scandinavian style: Cozy motives of Northern Europe (39 photos)
During the facing of the uneven surface, it is recommended to use the tile of medium format and SVP
Do glue like on the wall and on the tile itself with a toothed spatula. For alignment, catch the tile of Cyans and press your hand. Each step control the level. After identifying defects, you have 10 minutes to eliminate it to set glue. Otherwise, it will have to consider the solution and begin again. The seams are fixed with cross or clins. Work in small segments so that the lower rows have time to dry and not shifted.
Possible consequences
If we put the tile on an absolutely unprepared uneven wall, there will be no problems in the future. Of course, much depends on the degree of curvature, but in general the consequences can be divided into the following categories:
- Speakers. The most frequent problem. Due to the level drops on the wall surface, namely, there are exactly difficult to put the tile. When adjusting the corners protrude over the adjacent elements on the one hand and west in the solution with the opposite. It is noticeable with large tiles.
- Wave-shaped surface. It is also difficult to fit the level for mosaic and small parts, therefore, wave-like drops arise on a factionable plane.
- Uneven joints. When fitting the tile, wide seams are formed between the elements, and the influx is not excluded, which is even more unwanted. Partially eliminate this defect can be using a grout.
- Weakening of the decay of the solution. With an increase in the layer of adhesive composition, its properties worsen, the mixture slides or crept over time. In addition, the costs of glue increase.
- Education void. When applied to a thick layer of the solution to completely eliminate all the depressions under it it becomes harder that leads to masonry masonry.
- Destruction of the tile. If the load is loaded during surface irregularities, over time it will burst under pressure.
Article on the topic: Wallpaper lemon color in the interior of different premises
When cladding not prepared plane, masonry defects are inevitable
To avoid such problems, it is recommended to perform in advance at least minimal surface leveling work. If the situation is not so critical with the walls, in the case of facing the floor of irregularities is unacceptable.
If it is impossible to make walls perfect, use the methods described. It is advisable not to abuse them, as in the future it will inevitably affect your repair.