How to make mezzano do it yourself? This will be discussed next.
Andresol is a small or pretty roomy shelf under the ceiling. It is usually located in the hallway, in the corridor or in the kitchen in the opening above the door. In small-sized apartments, sometimes they make it in the rooms of a very small size.
The constructed mezzanine in the corridor can occupy a fair impressive sizes, if it allows the width and length of the corridor: it all depends on the planning.
How to independently make mezzano in the corridor
As a rule, the desired things are removed on the mezzanine, which at the moment or the season will not be useful. They are hidden in this way, they are reliably stored and waiting for the moment when they may need, do not interfere and do not occupy a place in ordinary cabinets.
By the way, the apartments are not completed by conventional cabinets, even the furniture in the form of a "wall" has become more accurate and compact, with less capacity, and there are no small-sized apartments: there are many standard planners where mezzanine and built-in wardrobes are originally provided.
But if in the initial layout, such embedded shelves and cabinets are not provided or were demolished for some reasons, it is easy to build mezzanine with their own hands, armed with simple guidance with step-by-step manufacturers.
Consider the step-by-step instructions of the work performed. First you need to decide on the place where Mezol will be located. Check the walls on the subject of the presence of electrical wiring so that it is accidentally damaged.
Well, if the apartment is not low ceilings and a wide entrance hall or corridor. And even better - when there is an extraction hidden from a general review. But in most cases it is just a wardrobe above the head.
How to make meresol do it yourself? First you need to consider the type of the mezzanine. Most often it is a small wardrobe above the doorway with the doors. Doors can be replaced with a curtain or not close at all.
However, it is the mezzanine with two sash, it is best possible to enter the interior, decorating the film in the style of the rest of furniture or repair of the apartment.
Next do the measurements of the space, which will occupy the mezzanine, and make purchasing materials:
- Metal profile around the perimeter of the bottom of the mezzanine and for transverse crossbars that support the bottom (if the enezol is large or long);
- Sheet of plasterboard or chipboard for the bottom;
- Wooden bars for cross frame of the mezzanine;
- Dowel for mounting a metal profile to the wall;
- self-tapping screws to the wall and among themselves wooden bars;
- Small metal corners for fastening the end frame from bars;
- Loops for furniture for mounting the door.
Article on the topic: Toys from pumps do it yourself
Measure the height of the bottom of the future mezzanine. It is not necessary to do without the help of a level, otherwise everything will be done awry.
The order of installation of the mezzanine
Frame supporting the bottom, it is better to make from a bar or a metal profile. Aluminum profile is often used. To begin with, the markup is applied, on which the desired length of the profile is cut down. On the wall at the level of the floor-measured floor, several holes are drilled in a step of 20 cm - at the level of the Niza of the future mezzanine.
The diagram of the antlesoli device.
Reinforce profile with dowels. When using wooden plates you can do without self-draws. If the mezzano is large or long, then make transverse rails to increase the rigidity of the bottoms (usually they do in the corridor along its entire length: to put things and get them out of depths are not very convenient, but the shelves contain a lot of things).
The bottom can be made of laminated chipboard or drywall. To do this, you need to place and cut the desired piece in the size of the bottom. Next, you need to install the cut-out bottom on the profile of an aluminum corner, fixed on the wall around the perimeter. Now you need to lock the chipboard or drywall with self-draws to the corner.
The end of the bottom plate can be decorated with a decorative edge, lubricating the inner surface with liquid nails (this composition is very easy to glue the edge and still holds for a long time).
Next, the facade box for the doors of the mezzanine is collected from the wooden bar - a frame from BRUSEV, which is fixed with the help of self-tapping screws in the future opening of the wall, where the doors of the mezzanine will be attached.
Next will be needed small metal corners for the ribbon of ribs with each other from the inside of the frame. We will need to connect the upper and lower base of the frame from the bar on the top and the lower base.
Then you need to close the timber with a plastic edge (you can do this using an iron, smoothing the edge, heating the thermocons to 180 degrees, and it is possible with all the same liquid nails).
Article on the topic: How to tie a hood knitting needles: a diagram and MK for beginners with video and photos
Further on the attached frame from the bars you can hang doors using standard furniture hinges: attach them to the door and frame by self-draws.
You can make such anessol with your own hands if you wish almost everyone, and with a high-quality execution it will serve for a long time. Already ready purchased box may not come in size to your apartment, and it will be much more expensive.