Features of the installation of a metal door in the apartment and the specifics of the installation of the input unit into the wooden house.
Definition of the required tool
The advantages of the iron entrance block before wooden analogs are obvious. Basically, manufacturers or trading platforms, when selling a metal door, are subject to work regarding measurements and installation of their own products. Most often, payment for the installation of the door block is laid in the cost of the product, sometimes additional amount is charged for work. However, to establish the entrance design with its own hands a skillful owner is not difficult, especially if this will save the family budget:
| Type of services offered | Standard door block size (mm) | Middle value |
| Dismantling of the old entrance door | 860/2050 | from $ 3 to $ 20 / hour |
| Installation of a new metal door | 860/2050 | from $ 20 to $ 52 / depending on the complexity |
To the installation of the metal door to the entrance is to approach the marginal responsibility. It is worth estimating our own strength, stock patience and some tools. Even if the installation fails to be made by its own hands, then the process itself is still worth knowing a lot in order to control the installers.
Installation of the steel door design is assumed at the entrance to the apartment, so it is important to know that the canvas should open out according to fire standards. There are, of course, exceptions regarding the way to open the door, which were reviewed earlier.
When arranging metal entrance door, it is important to take into account the technological features of the building material from which the structure is erected. In order to dismantle for starters, and then install the door block, you will need this tool:
- Construction level;
- Middle Size Lomik;
- Nail holder;
- Perforator or shock electric drill;
- The owner of a wooden house instead of a perforator will need a hacksaw and chainsaw;
- The chisel is needed in order to establish a block into a structure from a bar;
- Depending on the fastening method: anchor plates, self-tapping screws, steel rods;
- Construction foam for filling technological gaps.
Article on the topic: Selection and rules for installing loops with a door closer
It is worth paying attention to that if the package of the block does not assume the presence of anchor bolts, then it is permissible to purchase themselves. These are simple hardware products, the length of which up to 15 cm. The diameter of the bolts acquired will depend on the mounting holes in the box (usually d = 12-15mm). Segments of the steel rod, which are mentioned in the tool list can be approached.
Installation of iron door
Dismantling door
You can install a new entrance door with your own hands in just three stages:
- Dismantling the old design;
- Preparing door opening;
- Installing the iron door.
Remove the old entrance doors in the apartment so (mostly wooden):
- Provided that the door canvas worked on the collapsible loops, we approach it in an open state crowbar or another lever. So the cloth raises and jumps off with a loop.
Provided that the loops are not collapsible: you need to unscrew the screws that hold the door in the box using the screwdriver or the screwdriver.
- An empty box is dismantled with its own hands is not difficult if it is wooden. For this, the attachments (visible) are twisted: self-tapping screws, anchor, and nails are turned out. With a strong hold of the box in the opening and the inability to remove, its side racks are cut and parsed. After that, the lower and top units are removed without any problems.
- If the metal box is dismantled or the wooden box is attached to the anchors, it is easier to sprinkle with a grinder, like metal racks.
- Next, hesitates from the old insulation, the remains of plaster, protruding fasteners and other things.
Subject to the previously performed mechanics of the doorway under the new door, it must exceed the box around the perimeter for a couple of centimeters. It is necessary in order to be enough space for aligning it in the opening. With a previously allowed error during measurements, you will have to work hard, expanding the passage of the grinder with a circle around the stone. With too broad opening, it is permissible to narrow it with an additional cement mortar. Metal box to the doorway can be attached in two ways:
- through the technological holes in the bond profile;
- Using the use of mounting special plates.
Article on the topic: Shower cabin with a deep pallet
Install the box through the holes in the profile is permissible, provided that the wall thickness exceeds 150 mm, otherwise the box is easy to snatch from the wall with the web. We put the entrance design:
Installing a box
- The doorframe without a canvase is installed in the opening. For it, wedges are laid from wood necessary for fixing, adjusting its position and to ensure technological gaps.
- Adjusting the position of the box, proceed to drowning holes in the wall through the previously done holes in the profile: in a depth - 15-20 cm. Inverted sockets, anchor is revealed, the position of the racks is revealed. With the right position, the anchor is twisted and covered with decorative elements under the color of the box.
- Further on the pre-lubricated loop, the door canvas is hung, all the fittings are attached. The canvas is covered, and the gaps are checked around the perimeter of the rack, which should not exceed 4 mm.
Installing Door
- The functioning of all latches and locks is checked. Inaccuracies are eliminated by clins. The holes are drilled under the second rack, which is also fixed and check for the smoothness of the door canvase, locks.
- The technological gaps between the box and the opening of the wall are filled with foam, which should be sinking at least 24 hours. After which the residues of the foam are cut, and the surface of the wall is sweeping. Installation completed.
Installation of the door block on the plate is one of the most common ways and is somewhat simplified for the work of work with their own hands. Often, metal structures are equipped with mounting plates with harvested holes under fasteners, which are welded directly to the box.
Allowed errors
Construction of the entrance door
From a technological point of view, setting the door metal products at the entrance is not as difficult, but it is worth the subject of responsibly, since the care of the work in the future guarantees the quality of the construction of the structure. Often allowable errors during mounting work are reduced to the following, which is worth knowing before putting the product:
- The disk of the door box is imprisoned in improper alignment of it relative to the vertical and horizontal.
- The irregularity of the installation of the doors depends on the thoroughness of cleaning the seating area.
- It is more difficult to put the entrance door in the panel houses that the armature can be caught under the anchor, which will lead the fastener to the side. Avoiding such an error is permissible using metal thrust that shift the drilling point of deep into.
Mounting the iron door in a wooden house
Log houses with time give a significant shrinkage. Working with openings in a wooden house is not worth the same barbaric way as other materials. It is extremely not recommended to score pins in a ram with a length of 150 mm in a wooden opening. Tips, how to install the iron door in a wooden structure on your own:
- In the finished opening of the end wall in the house, vertical grooves are filled with pacles. In the specified grooves it is worth installing both bars for sliding. The number of grooves the number of fixing points is equal to the number of fixing points.
- In the opening you need to put a special cluster, it is fixed to the bars of sliding with self-draws. The gaps on the racks in the house should be 2 cm, according to horizontal crossages - at least 7 cm, in order to do so in a year, the shrink shrush did not swap the door.
(Your voice will be the first)
Loading…
Article on the topic: Apply for Balcony Repair: Subtleties of Legislation