Installation of the door-coupe according to the instructions. This can be done on your own - you only need to follow the procedure and use high-quality fittings.
How to install interroom blocks and compartment independently
Interior doors-coupe, demanding less space for themselves, certainly attract the attention of the owners of the rooms, where they are registered every square centimeter of the useful area. At the same time, the installation of such products requires certain skills, since structurally such doors are more complicated by the usual swing. Therefore, a qualified installation of the door-coupe is important not only from the point of ensuring their durability, but also for the convenience of everyday use.
There are two varieties of such products: embedded in the wall and hanging on it. The difference is that for the first version it takes another preliminary preparation of the wall at the doorway: it takes a niche under hiding a cassette there with a door clove. Subsequently, this niche is closed with a decorative panel, for example, from drywall. Aesthetically, this option is better, but it is suitable only when a major overhaul is a major overhaul associated with the reorganization of the walls.
If a more modest task is set - to replace the swollen door on the door-compartment, with your own hands, then more acceptable option with a hinged door design. However, in this case, it is necessary to take care that the part of the wall adjacent to the product was free from furniture or other design forms (outdoor VAZ, aquariums, etc.). The choice of free space depends solely on the internal features of the room, since the door-coupe can be hung with its subsequent opening both to the left and right (this should be informed about the assembly instructions with their own hands).
The kit of the coupe consists of:
- actually door leaf;
- opening mechanism;
- decorative panels;
- Required door fittings.
Article on the topic: Guidelines for the construction of the design of the frame house with their own hands
Sometimes accessories in the volume of ordinary delivery is not included. Then steel guides, a set of roll-out rollers are acquired to install the coupe (in no way plastic!), Pens under the style of the room, which will connect the door, and fasteners. The assembly will also be impossible without a wooden bar with a cross section of 50 × 50 and a length equal to the double size of the door canvase.
The most common range of available interior doors-coupe is set within the following limits:
| Type of product | Section width, mm | Section height, mm |
| Standard | up to 900. | 2130; 2290. |
| Under the order | 1086-2354 |
Preparation for installation
Width of sliding systems
Installation of interior door-coupe, with your own hands, begins with checking the compliance of the fit door to the dimensions of the doorway. It is necessary to decide what it will be easier: pick up the goods under an existing opening, or to adapt the opening under the selected size of the door-coupe. Estimated dependencies are very simple:
- For high-rise size of the NDV = NPR - 40 (mm);
- For the width of the opening of SDV = SPR - 20 (mm).
For non-standard products, instructions should be attached to the desired size.
Next, the flatness and tilt of the floor are checked in the zone where the installation is to be installed. In the presence of slopes, the door-compartment will either hardly close, or easily go to the opposite direction. If it is impossible to correct the floor defect in any way, you will have to additionally purchase a set of clamps.
It is useful before starting the installation of the doors with your own hands, view the video where all the steps of operations are consistently.
Installation of blocks
Mounting work
The assembly begins with the bottom of the door coupe. At first, in the floor of the opening it is necessary to perform a groove where the door canvas will move. Installation of the guide is made in the groove, and the guide rollers are mounted on the surface of the door canvase. Previously, it is necessary to check the width of the guide width of the door (the difference must be twofold).
Article on the topic: Installation of rolled curtains yourself
Installation of the door with your own hands is convenient because it is possible to set the horizontal displacement of the door web, after which it is temporarily consolidated by its retainers. After that, the door is inserted into the upper guide, and a wooden timber is installed above the door opening, which is then attached to the wall, and the upper guide is mounted on it. Next, without fixing it, check the ease and correctness of moving the door leaf on the rollers as on the video. If the door of the door is smooth, then the upper guide can be attached finally.
Sometimes it is limited to the installation of only the upper guide, but it is guaranteed to avoid the jamming, only when the door-compartment will move towards both the bottom and on top.
To secure rollers, stainless steel screws are used, which, if desired, can be closed with decorative plugs, selected under the color of the door leaf or wall. The exact installation of the rollers is possible only when using a construction level and a plumb.
Installation ends with the final setting of the clamps, so that the door does not move spontaneously. After that, decorative strips are installed, the final assembly is performed and the stroke of the product is performed as on the video.
Design
Some features have an assembly of a product that does not have thresholds. Then limitated only by the upper guides, and the rollers of the mechanism must be mounted on the bearings. To reduce noise when moving the door under the guides, rubber strips are put.
The main feature and difference in the assembly of the door-coupe, which "hides" into the wall is the installation of a metal frame (cassette). The presence of the cassette significantly increases the stability of the product and its durability. If it is important, you will have to partially destroy part of the wall in the room or corridor. Made a cassette using standard metal products profiles - a corner or a schuler. In principle, it is possible to use the pipe, but then do not do without welding. The sizes of the cassette are coordinated with the dimensions of the door web, after which the frame is mounted in the niche provided for this and close it from the side of the plasterboard sheet.
Article on the topic: Walking wallpaper, the more convenient to apply glue, tool
Assembling the door-coupe with your own hands - the procedure is quite simple, it is simply necessary to carefully treat each stage of installation and accurately pick up the necessary decorative and fasteners.
(Your voice will be the first)
Loading…