The model lies on the basis of the design of a conventional direct skirt. In the talio line of the right shelf, an assembly was made. The fastener is asymmetric, with the smell in front. Corners are rounded.
This model is good for women with "unstable" waist volume. You can reduce or increase the volume by simply aligning the fastener (hook, buttons).
Such skirt can be sewn both everyday and as a "festive" option. Everything will depend on the fabric from which it will be made. You can choose any positive fabric, with the exception of transparent - crepe, chiffon, organza, etc. It is also better not to use highly enhancing fabrics.
The model looks great on all types of typical figures, eliminating the figure with a markedly protruding stomach (the assembly will visually increase it).
Build pattern.
Build the pattern of the skirt presented above the model can be based on the drawing of the design of the straight (2-sut) skirt.
1. Rear cloth without modifying.
2. We work with a shelf:
• From t. T1 (center) →, postpone the smell = 1/2 distances between the plotters + 1.5 - 2 cm, we put. T.5.
• Lower ↓ perpendicular from t. T5. On the line of Niza put the point H5. We draw up a smooth rounded line of the Niza right shelf.
• We apply parallel to the center before. cloth straight line simulation lines;
• Cut on scheduled straight, ranging from the waistline. We push it on the width you calculated (depends on the desired assembly volume (folds) and their widths).
• Pulling (right) is redistributed to the assembly.
• Do not modify the left shelf. The smell line coincides with l. Withdock, ideally closing it slightly. In the currently discussed model, the left shelves is not rounded, but, if desired, you can make a change in the model, rounding it, it will also be very beautiful.
• Next, you need to carve out the subcounting Ave. weld (Cleaner) in the form of an identical side of the panel, 6-7 cm wide. The left cloth, if the width of the fabric you choose is width, you can carve out with an all-circular overgrown, width that should be left with the right. In the drawing, it is indicated by a dotted line.
• Clear belt 8-10 cm - width, length = waist amount + smell + seams. Correct the belt to crumble at an angle of 45 ̊ (if the fabric allows) or not for the equity thread.
Article on the topic: Abazhur from rope - Macrame weaving technique
How to sew a skirt with the smell? Technological sewing process.
1. We make the assembly of the right shelf. We collect the top slice of the cloth 1-2 lines, as wide as possible stitch.
2. Gift the phlizelin (dublerin) belt and 2 fees.
3. We make the processing of the edge of the side.
• Free edges of the welders are processed by the "Overlock" seam.
• Fold the front sides of the shelter with adhesions so that the weld is under the paw. We pave a line by retreating 0.5-0.6 cm from the edge of the side.
• Having unscrewed the chapter on the "wrong", we sweep the chandel.
4. Mix and stepping out the locks l. front and rear cloth. Then, start them to the center. The foundation of the "slide" at the base of the molding should be subjugated by moving the iron "wave-like" movements. Do not forget to use a wet Peretüglik.
5. Sailing side stacks (you can preliminarily resignar). Scrolls of side seams are grouped (overlock), they are locked up to the center of the back.
6. The latter always sew the belt.
• Apply the belt to the upper cut of the skirt (belt above).
• We start it in half, bent at the same time the reverse side of the belt.
• Crane, and after turning both edges of the belt.
• We estimate to make it convenient to lay a decor eclipse. We deploy it on the front side of the belt, by 1 mm retreating from the suture of the feeding.
• Roofing.
• Wash loops.
• Sewing buttons.
Laying and approximate fabric consumption.
The skirt is straight, with odor, drapering, asymmetric coquette on the front right panel, decorated with decor clasp.
Asymmetry perfectly hides flaws from ladies with different configuration hips. The presented skirt model looks great on any types of female figures and has no age limit. It is possible to make this model from any, well-dreamed, incurred fabric.
Skirt with the smell pattern.
It is built on the basis of the base drawing (pattern) of a straight skirt (excluding points).
1. The back does not change.
2. T1T3 = length to l. Out.
3. Of the T. T3 we carry out perpendicular to the bottom, we obtain t. H3.
4. Beautifully rounded the corners on both shelves.
Article on the topic: Knitting toys with knitting needles
5. Close P. Front Outcast. Stop smooth line of coquetki.
6. At the bottom half, the details of the right panel need to strike the lines for which the slip will be made (see figure).
7. Cut, starting from the top. Do not upgrade to Niza about 5 mm. Spread in the form of a fan, so that the line width does not change.
8. Recalling the dial chalk configuration (6-7 cm wide)
9. Crow belt.
Technological sewing process.
1. Matching and stepping. Sangered with respect to the center, the base at the base.
2. Send an assembly (or lay warehouses) 2 straight lines, maximum width stitch.
3. To impose a coquetka to the bottom item, fit, and then stagge into each other, leaving the allowance ~ 1 cm.
4. Verify the allowance. They have something like "watched" on the coquette. The front side should be laid a decor eclipse, preferably silk thread.
5. Skin the adhesive adhesive, after spending.
6. The weld and the shelf are folded "face to face" and roll.
7. Soak. Let's pull out a chandelier 0.1-0.2 cm. We deposit the protrusion on the front side of the part. Remove extra threads. Revenge.
8. Breaks, the bottom of the rear cloth is started. It is powered by manually or on a typewriter.
9. Scattered and accelerated side seams, leaving the allowance of 1 - 1.5 cm. Next, they are cooled and rooted in the back direction.
10. The belt is treated top.
11. Restore the finished thing.
12. Loops break through. Sew 3 buttons.
Photo examples:
