In this article we will talk about how to make a forget-me-not beaded with your own hands. This kind of product is very beautiful and original decorations, looking at the photo, you will be sure about it. They are used in the interior design, in various topiaries, key chains.
Blue Flower and Leaf
For this master class, we will need:
- beads (blue, yellow and green);
- wire with a diameter of 0.2 mm;
- pliers;
- Aluminum wire with a diameter of 1 mm (it will be needed to form the main stem);
- Also prepare green threads, they will be needed for the design of the stem;
- Wicker basket, a decorative vase or a beautifully decorated pot (we put a ready-made bouquet of forget-me-not).
So, proceed. Our work will start with separate forget-me-not. Take the wire and with the help of pliers "bite off" a segment of 20 cm. Take six blue beads on it and then place them five cm from one of the wires. Skip it in the opposite side through the adjacent bead from the reverse end of our wire. Using tightening, it is necessary to arrange the wire so that the residual length of its end is five cm.
If the whole algorithm was done correctly, then you should get a beetle loop. Now make a similar loop and type six blue beads on the long part of the wire. Skip it through the first loop in the opposite direction. Tighten all the beads tightly and remove the formed empties. At this stage, you must have two loops.
We need five such loops, so with the help of a specified algorithm, make three more loops and place them all close to each other. Miss the remaining end of the wire through the bead, which is located on the base of the first loop. Try all the product to drive to the center of the future flower. Connect all loops into one to formed flower. Type the yellow bead and skip the wire through the beads of the fourth petal (loops). Scrub both ends of the wire together. The first flower is ready.
Article on the topic: How to make a dream catcher with their own hands - 11 best master classes
Take green threads and wrap the wire under the very reason of bud. In order for you to have a bouquet, you need to make a lot of forget-me-not. Calculate in such a way that you have about 22 non-discharge buds on one flower. The number of colors adjust yourself, the main thing is that their number is not less than three.
Use green beads to make leaves.
They are made using the technique of parallel weaving on the wire, which must be at least forty see.
Scheme: 1 row: Slide one bisery; 2 row: Take two bispers; 3 row: Take three bispers; 4 row: Locate four bispers; 5 row: Hang five beads; 6 Row: Locate six beads; 7-10 Rows: Learn seven beads; 11 Row: Locate six beads; 12 Row: Lock five beads; 13 row: Locate four bispers; 14 row: Learn three bispers; 15 row: Learn two bispers.
Take the thread of green and wrap it with a wire under the leaf. Length - about four, see of course, one leaf for a flower will not be enough, so if you want to see a bouquet of lush and complete, make such leaves ten more.
Step-by-step assembly
After all the elements of the bouquet have been completed, you need to make a flower assembly. First twist all small flowers three pieces. If for each flower you made 21-22 small flower, then you should get seven pieces per large flower. Take green thick threads and wrap each stem under each inflorescent about three cm long.
Now prepare a thick wire from aluminum or copper (approximately 1 mm in diameter), we will need it for the main stem, about 15 cm length will be sufficient. If you do not have such a thick workpiece, you can take several thin wires and weave them among themselves, you will have a cable that will be durable and completely comes up for further work.
Article on the topic: Homemade shoes do it yourself
So, screw to one of the ends of the thick wire first one inflorescence. Now wrap the stem for three centimeters in length all the same green threads. It is necessary to do this carefully so that the wire does not break the wire. Further after each other, evenly distributing them throughout the circumference, attach to the main stalk.
Continue to wrap translucent parts by thread. When all breast-meal buds are attached, place the leaves. Make them approximately at the same level. Now inspect all the work and correct the irregularities and small shortcomings. Collect your charming bouquet and position beautifully in a basket or a vase.
Video on the topic
Thematic video selection: