In this material we will talk about weaving and how to make daffodils from the beads of different sizes. This kind of product becomes very beautiful and original ornaments, as can be seen in the photo below. They are used in the design of the interior, in various topiaries, key chains and even broochs.
Yellow flowers
Many argue that the yellow flower color symbolizes and foreshadows separation, but we know that it is not. It is enough to remember how the Narcissus blooms, how much joy he delivers his beauty, and his yellow bud as a sunshine, which swings on a thin leg. How much good and charm in themselves carry these flowers. In this lesson, we will tell you in detail how to make Narcissus hands.
For this master class we will need:
- beads (yellow, green and white);
- wire (it is desirable to choose a material with a diameter of 0.3 cm);
- Lamps (to cut off wire at the right moment).
All this can be bought in the store, which specializes in needlework. After you have prepared everything you need, you can proceed to work.
We will start with the petals, for this, in a wire inhale 14 white beads and make an arc. Repeat this technique until you get nine arcs. This is a calculation for one petal. And for a full-fledged flower, you need to make five petals, therefore, you will have forty-five arcs.
When your petals are ready, you can move to the heart. Squeeze 30 cm and remake from the wire from the wire the desired cut. Take 16 beery on it and bend in half. You have to get a loop. Take a similar segment of wire and thread it across six beads, which turned out from the loop. You should have two ends of the wire that go out of beads.
Article on the topic: Silk painting: Master class for beginners, drawings and equipment
On the first segment of the outgoing wire, put on ten beads and twist them in the loop. Thus, continue weaving until 15 loops succeeded from twisting. Turn all the product to one side to the bottom and to the other side to the other side of another segment of the wire.
Take on it only one beading and thread across six beads from the first loop, make twisting. You must get a set of closed loops. In a new wire, inhalt three bispers of green and tighten them from below. Our all details are ready, it remains to collect them in a single flower. Using a set of yellow loops, sort a long wire with a green beads in a circle. You got the core. Now you need to attach petals.
First, the first three are attached, and then two others are neatly added. All segments are twisted with each other.
Note! Try to do all actions with very tight consolidation so that our product does not fit.
Our adorable decoration is ready. You can create a beautiful bouquet of daffodils. To do this, do the entire master class as many times as you want to see colors in your bouquet. At the end, you can beautifully arrange them in a decorative small vase, and your solar mood will not leave you.
Technique parallel weaving
In this section, we will consider another option of weaving. This method is called a parallel weaving technique. You will need a lot of patience and perpetuity, but the product will be neat and even.
To do this, you will need:
- beads (white, green, orange and red);
- Wires (it is desirable to take a diameter of 0.3 cm);
- Good light (you must make sure about good light. It is better that it was daylight, if there is no such possibility, then use the desktop lamp).
Article on the topic: How to bookmark paper for book: Corner video and photo
And so, proceed! Let's start our work with petals. The whole process must be done according to the attached scheme:
Take the wire and with the help of white beads. Perform a weaving that according to the scheme: one, three, six, eight, ten, twelve (do the algorithm three times). To make a small petal, take advantage of: the tenth, eighth, sixth, fifth, third, second schemes (repeat three times). For the manufacture of a large petal, take advantage of: twelfth, tenth, eighth, fifth, third, second.
For one middle Narcissa you will need three small and three large petals. For the core, take 60 cm of the wire segment and type 1 green on it, 1 red and 3 yellow beads.
Now go to the core. We undertake a wire of 60 cm long and score 1 green on it, 3 yellow, 1 red and 3 yellow beads. Skip the wire end through the first bead. Type 5 red beads on the working wire and skip the end through the top red. To make sheets, it suffices to follow the proposed schemes: 12-10-8-5-3-2 (65 times); 10-8-6-5-3 and 2-4-7-10-12-14 (3 times); 1-3-6-8-10-12 (2 times).
All the details of the flower are ready. Gently make the assembly of all parts. Our charming product is ready!
Video on the topic
Thematic video selection: