In each house, a large number of little things accumulate over time. In order not to look for the necessary details in different places, it is necessary to organize a single certain place for small items. How can't the way here will be the purchase of a special box or box. But not necessarily buy it. Fans of needlework usually create a box for little things with their own hands from the simplest materials.
Order in small things
For the manufacture of such a drawer you need to have:
- Corrugated 3 mm thick cardboard;
- stationery knife;
- scissors;
- line;
- bilateral scotch, instant glue;
- miniature magnets;
- pencil.
As a basis, you can take a finished box of the box or construct a template to your liking.
Deciding with the size of the drawer, you should cut 5 parts from corrugated cardboard.
Remember that three details should be slightly shorter than the remaining two. The width of all billets should be identical and match the double height of the box.
For the strength of the product, the template should be located across corrugated waves.
Along every detail on the inner long side, two parallel lines are stated with a sharp knife. The distance between them is 5 mm. Lines should be located strictly in the center of the workpieces.
Parts are bending along the outlined notches. At the edges of the parts at an equal interval, cuts are carried out with a width of 3-5 mm. Internal fold of each part is also subject to cross-cut. At the same time you need a little retreat from the edges. A pair of cardboard layers is separated between the central notches of blanks from the inside.
Details are folded over the collar and insert one to another, forming a grid.
It's time to proceed to the manufacture of the foundation. To do this, a pattern of a specified size is generated from the cardboard. On the corrugated line, burning and cuts should be taken, drawing on the presented photo.
It is necessary to pay attention to that in some extreme parts, the cardboard layers are separated, leaving thin areas.
According to the created recesses, the cardboard is bended. Single-layer areas are peeling inside.
Article on the topic: Autumn Ekiban do it yourself from leaves for school with photos
A separate sheet of cardboard is taken for the cover, from which the part of a given value is cut.
In some areas you need to make the discontinuation of the cardboard, as shown in the figure.
The inner parts of the lid and base are cut separately.
Details for the box should make slits.
Pre-work performed, it remains to collect parts together. Thin wide portions on the base of the box are lined on the inner side.
The inner part of the box is strictly in the center of the base.
Next, you should position the harvested grille at the bottom of the box. In the slits on the short sides, glue poured. The side parts are inserted into the slots of the lattice and the bottom at the same time and pressed. You need to wait for the moment to grab glue.
Such a procedure is done with two remaining walls of the box.
In the center of the cover, from its inner side, the previously harvested part is glued. The edges of the lid are twice and glued together.
The side parts of the parts are fixed on the inner layer of the lid. Here you need to consider that the glue is applied to thin pieces of cardboard.
Small single-layer parts are bonding on the inner side.
Lastly, the remaining two sides of the long edge are formed.
The box provides magnetic rivets.
To install them, you need to cut through the central part of the front bases of the base and the cover of two small holes with a diameter coinciding with the size of the prepared magnets.
It is important to consider what holes should not be through.
Using the instantage glue, the magnets are fixed in the sockets.
Now you should attach the lid to the box. You can do this with the help of small loops purchased in the shop of fittings.
But there is another way. This will require a subtle corrugated cardboard (1.5mm). Two plates are cut out of it and attached to the rear parts of the covers and boxes from the outside.
A plot of cardboard, which will be open (along the fold line), is not processed by glue.
Article on the topic: Crown for girls do it yourself from paper and cardboard with photos
It remains to decorate the outside of the box with a planned composition. Ideally fit into the product decor with the use of decoupage techniques. And the design of the box scrap-paper will allow brightness and unusual in it.
Comfortable drawer cells will systematize small details in the form of buttons, beads, etc.
Focusing on the presented master class, you can create modified boxes in which the number of cells will be increased, or create several similar products for the items of different purposes.