The corridor is the first room, which is visited by every person who has entered the house or apartment. And it is this room that meets homemade household, happiness and family. Therefore, the room facing is very important for the future interior. The corridor finishes the MDF panels is increasingly gaining popularity, so we consider it in detail. What are the pros and cons of MDF, than can replace the material, how to install it and care for it. We will give all these questions a full response in this article.
Advantages of MDF.
The finely dispersed fraction (abbreviated MDF) did not just become popular. It has a large number of advantages that allocate this material among others.
- First of all, the decoration panels is very easy and simply performed. It does not need special materials or tools for it. Basically, in each house you can find those devices that need when installing MDF.
- Easy clean and washing. If the wall has been contaminated with anything, the stains are very easy to eliminate simple wash or wet cleaning.
- Universality. A hallway can be performed using panels not only on the walls. Sucks, doors and ceiling can also be treated with such material. And since the corridor is not a residential premises, then for him MDF is especially suitable.
- The cheapness is always attracted by very many buyers. Compared to plastic, such a panel will be a bit more expensive. But if you take for analysis wallpaper, paint, stone or tree, MDF panels will be much cheaper, stronger and more durable.
- Finishing with such a material does not require additional hands - even one novice is quite enough to perform everything immaculately. And attracting specialists - is not at all necessary.
- Environmental Safety. Many construction specialists have argued many times that chipboard, plastic and even wallpaper can affect the health of residents. In contrast to these materials, MDF is a tested material and with accuracy can be declared that it is environmentally friendly.
Given all the positive features of these panels, you can unambiguously make a choice in its direction. Moreover, now in stores there is a fairly wide range of MDF types. It can be performed in any design - in a tree, a flower print, a monophonic version, etc. Selection only for the buyer. As for the minuses of the material, they can only be attributed to them that the panels are afraid of moisture and they cannot be used in open areas, on the street. They are rarely used in bathrooms, toilets.
Finishing instructions
The easiest and necessary advice for everyone - create a plan for finishing a corridor on the leaf, to paint completely all sizes, room parameters and the amount of material.
If you clearly decide that the finish must be performed solely with the help of MDF, then it is worth studying how to install it correctly. Here are some nuances:
- Preparation of walls. It is worth carefully cleaning the surface, launching large holes and irregularities. The panel is capable of hiding only small defects. If the hallway is made with beveled corners, then immediately need to align them and make even.
- Insulation. Before installing the strips themselves, it is worth insulationing the room. It sounds better sounds a corridor and it will become warmer. Under the selected material, you can use any of the existing types of insulation. Even fat fiberglass is allowed.
- Frame. When the insulation layer lies smoothly and smoothly, you can proceed to the creation of the cutting. Its necessary to perform from wooden planks wide with a width of about 3-4 centimeters. The distance between parts of the future lattice should be about 30-40 centimeters. Immediately mounted lower and upper strips, then side and internal. Do not forget to use the level in order to respected direct angles in this crate. From the quality of the frame, it will be directly depended on how the decoration wall will look like.
- Installation of the first strip. This moment acquires a particular importance because it will start the first one - it will go. Be sure to first element must stand 100% vertically, under the level. Otherwise, you will have to cut the subsequent strips on both sides, which will more and more mow. The first MDF board is installed using a special fastener, which is one side enters inside the strips, and the other is attached to the frame of nails or self-drawing.
- Laying other parts. Next, each brand MDF will enter the grooves of the previous one. If you do not want the wall with time inserted - you can also use a special fastener for screwing to a frame. Use conventional wood screws to comply with strength conditions.
- Edge processing. If only walls with panels are processed in the corridor, and the ceiling will be different - then the upper and lower part of the installed wall of MDF can be covered with a special corner. It covers all the headlock edges and creates a very stylish look.
The main stages of the corridor finish with MDF panels we have considered. It is clear that in this case there are no big difficulties, but still there are small nuances. Consider this:
- The corner for the edge of the slats should match the basic material motif. Pick both the first and second - right in the store at the same time.
- If the inlet door and the input opening are made of MDF panels, and the walls are planned to be performed using it, it is better to distinguish between the color gamut. For doors, it is advisable to choose the colors "under the tree", and for the walls and the ceiling - any other.
- Remember that for the corridor and the hallway, a small place is often given, so it is better to carry out the processing of walls in light pastel colors. The use of black, gray, brown - is not inappropriate, especially since MDF is very good.
- Comparing the material with plastic, remember that the MDF is much stronger, stable damage. Panels with a thickness of about 0.5-1.5 centimeters and are environmentally friendly.
- It is convenient to use the MDF panels only for a specific part of the room. For example, the lower half of the corridor from such a material, and the upper thing is to salary. Often, the bottom is drawn up with a decorative stone, and the top is based on the panels.
- Be careful when choosing and buying a material. The store should pay attention to the edges and grooves. They may be damaged during transportation and create not such a spectacular and immaculate view of the walls.
- Better to acquire a screwdriver for the design of walls with panels. They will have to fulfill a lot of things - to fix the insulation, build a frame, screw fasteners.
At the end, I would like to wish patience every newcomer in such important matter. This is although it is not very difficult, but it will be very good to calculate everything. Exactly calculate how much material you have and how to cut it better. Successes!
Video "Recommendations for Finishing Corridor MDF Panels"
The record shows how to properly separate the corridor panels MDF.
Article on the topic: Metric for Girl Embroidery Cross Schemes: For Boy Children's, free download, Sets without registration