If the dimensions of the doorways for the most part are standard, then the walls in different buildings are the most different thickness. And the door block both interroom and the input consists not only from the canvas, but also from the box. The width of the latter varies in a much smaller range than the thickness of the walls. Dobors and platbands at the entrance door solve this problem.
DOWERS on the entrance door
What it is?
In fact, it is a plank from a suitable material - wood boards of the appropriate breed, DVP, MDF, chipboard with cladding and without. A cooled material can also be used, for example, cellular, lined with MDF sheets, and so on.
The appointment of a good board is the overlap of the slots, forms between the wall and the door frame. This is often because the walls in the apartments do not differ in perfect verticality. However, the planks can do not fully implement a functional role. If the thickness of the slope in the doorway is too large, the standard box simply does not overlap the surface. Dobly planks are selected for the color and texture of the box, and overlaps with an open surface.
Before and after installing good
Most often this operation should be done when installing metal entrance doors, as the width of the opening is always greater. You can make the bar and alone, but only wooden.
Varieties of good slats
Dobors and platbands are produced in various sizes - from 7 to 40 cm. In addition, telescopic models have the opportunity to increase width. In large hypermarkets, like Lerua Merlin, you can always find platbands of any size.
Class plates on manufacturing material:
- Tree - oak, ash, wenge, is still a popular material, since it is very beautiful, relatively affordable and thanks to the processing - grinding, lacquer finish, with antiseptic finish, is distinguished by durability;
Wooden Dobors
- MDF - wood material, characterized by good moisture resistance, which for entrance doors is an important quality. However, this property strongly depends on the quality of the upper layer, imitating oak, cherry, wenge. In cheap versions they are laminated paper, which in itself is unstable to water. As a result, the details are losing the color much faster than the frame go door canvas;
MDF DOPORTA
- Plastic - on the one hand, the material is not afraid of moisture and does not lose the appearance, on the other, it is not so good imitation of the tree to confuse. Despite these plastic elements are popular because it is easy, cheap and very easy to install;
- Ceramic dobors on the inlet metal doors are a rare option, as it is intended mainly for the design of the entrance door imitating the stone. Ceramic details are extremely durable, wear-resistant and very beautiful. However, ceramics are rather fragile, so installing elements with their own hands undesirable. In the photo - ceramic elements.
Article on the topic: Fastening profile for drywall - Methods and their nuances
By its design, the challenges are divided into 2 groups:
- Direct is the usual slats with a thickness of 1-1.6 cm and a width of from 7 to 40 cm. They are easy to fasten into the opening with glue or nails. Planks can be with the edge and without. This option is installed in a couple of dozen minutes with their own hands on a metal entrance door;
- Telescopic - planks are collected according to the principle of "spike in the groove" and have the corresponding elements on the sides. Thus, you can close the slots of any size and block the slopes of any width. They are somewhat more expensive, but it is more difficult to establish them.
Two types of construction
Installing Dogs at the entrance door
Mounting dobors and platbands are preferably along with the installation of the door frame. However, this is optional. You can also select elements with the entrance doors or later. A wide range of Lerumamer allows you to find the most suitable material.
Straight planks are completely simple: the holes for the self-tapping screw are done, screw the strips and seal seams. Installation of telescopic harder.
- First, in the finished door frame you need to make grooves so that you can connect the frame with the planks.
- According to the contour of the box, the frame is fixed from individual strips of plasterboard or plywood.
- Cut in size vertical and horizontal dobors according to the size of the box elements.
- The grooves are lubricated with mounting glue to ensure more durable mount.
- Then insert goodness and expect until the glue composition freezes.
- Remove the temporary framing and install the door frame in the opening. It is important to achieve complete alignment. The verticalness of the side slopes is adjusted using horizontal struts and check by slope. The horizontal of the jumpers are achieved by mounting side wedges.
- The mounting foam close up the gaps to achieve one level with a plastered wall.
- Install platbands and plinths.
If a quarter is not selected on the box of the front door, it is difficult to alternately by the frame of the frame. At the same time, the mounting glue is used - it is applied by portions every 100-150 mm. When the mounting foam dries, the cracks will be filling.
Article on the topic: How to quickly get rid of mold on the walls
The video demonstrates the installation of sobers to the inlet metal door.