Entrance doors are not only the protection against cold and thieves, but also a beautiful fashion accessory to enter your home or apartment. Nowadays, a variety of materials are used to make door cauldons, for example:
- metal,
- wood,
- plastic,
- MDF and others.
The process of installing the entrance door
Do you think that installing the entrance wooden door do it yourself - is it hard work? You're wrong. Even when for some reason you are reluctant to install the doors on your own, you can at least check the installation process by their master.
If you decide to do it yourself, you will need some tool:
- Lomik or Nail)
- level,
- Perforator.
The door wooden entrance with the box is usually sold complete with all the necessary details.
Dismantling door luttik and doors
First you need to find an assistant, as it will be difficult to cope with this work. After you need to get rid of the old door leaf and the logs, and then you have to do install.
How to dismantle the entrance door? The first thing to do is to remove the door leaf with the loops. How will you do this depends on the design of the loops on which the doors weigh. They are two species:
- Detachable. Remove the cloth from such canopies is quite simple. It is necessary to open it at an angle of ninety degrees relative to the door frame and lump fit on the side where the loops are located. Rocking movements up and down to remove the door canvas.
- Inseparable. It is a little different with them: taking a screwdriver or a screwdriver, you will need to unscrew the screws that the doors are attached to the box, and remove them aside.
Article on the topic: What is better to choose a tile or bathroom panel?
After that you need to get rid of the old door box. To remove the wooden frame out of the opening, you need to make rods at an angle across the side racks and remove it by mounting it. How to do it, look at the photo.
When you removed the Lutka, you need to clean the opening from the garbage and the rehabilted plaster.
Do-it-yourself entrance door do it yourself
Many people think that make the door with their own hands is very difficult, but it is not. First you need to choose the material - the quality of the system will depend on this: service life, appearance.
The manufacture of wooden entrance doors can be both coniferous rocks and deciduous. The most important thing is that they are properly sucked. Before embarking on the assembly of the door system, the tree should be treated with a special tool that will protect the design from different types of pests and external factors.
The first box is performed. It is made from a bar bonded with spikes. Now proceed to the manufacture of the canvas. The simplest system is the viper.
The video shows how to make an entrance wooden door on the panel technology.
Preparation of the opening for installing inlet wooden doors
If it so happened that the door block does not fit the mind, then it will be necessary to fit it under the desired size. For example, you have a box more opening, it means that you need to increase the opening with a perforator or a grinder with a circle around the stone. And if the box is smaller, it will be necessary to reduce the opening with brick and cement mortar.
Installation of wooden entrance doors
Let's start directly to install the door with your own hands. After you prepared the opening, you need to properly set the box. It is done with a plumb or construction level. Installation of the door box need to be produced without a canvase. When all is exhibited, we take wooden wedges and insert them between the opening and the frame. Now you will need to hang the door on the canopy and check how it closes.
Article on the topic: Houses projects Drawings
If the work of the door suits, remove the web with the loops and secure the luttka to the wall. The mount is made by nails or screws. In order for the design to be stronger, you can fasten special metal lining to the frame. They are put closer to the place where the castle will be, and where the loops cost. Such a solution will give your input stiffness. After the mounting plates are installed, the fasteners are taken (nails or self-tapping screws) and the box is fixed. After that, again inspired the door to the place and check whether the installation was not rushing and it is not necessary to adjust the loops. Now you can finally install the wooden entrance door.
When you all checked and fitted, and the result is satisfactory, the slots between the wall and the frame can be filled with the mounting foam. This will give extra strength.
To give the Ophetical View to the Operation, the extension panels are set (DOP). They can be made from both wood and fibreboard. When installing, it is necessary to observe the procedure: the first to install vertical, and then horizontal, as in the photo.