If you want to learn new skill, then weaving bracelets from color tubes will definitely interest. Is it possible to make something from such a material and how to work with it below. We will need fantasy, inspiration, luck and some free time.
Basic of labor
Such a weaving got the name of Scoobid (do not confuse with a cartoon and a dog). In France, in the 20th century there was a performer who wrote a song with the same name. Fans to please their favorite-idol, made a memory bracelet made from the tubes. So they gave him their love.
Probably, so weaving is especially popular among children and adolescents, as they are young and bright, and often show their love and care through the creation of souvenirs. The manufacturing technology is very lightweight, especially suitable such a lesson during family evenings - you can consult, boast and give a gift.
Plastic harnesses are used for operation. They have different sizes, and the colors are more than the rainbow. The length is varied - from 80 cm to 100 cm. There are also tubes can be round or flat.
There are two types of weaving - square and round. They are distinguished by appearance and complexity. In the easy master classes for beginners, everything is described in detail and is shown, so there will be no problems with execution.
Square woven from four harnesses:
Round woven in the same way:
Both weavings begin equally. The length of the tubes must be 3-4 times the length of the product. You need to take 4 harness of different colors, tie them into a nodule. This is the beginning of any work. You can use 2 harness to make a accessory, but then they need to be tied as shown in the picture.
Article on the topic: Snowdrops from corrugated paper with their own hands with photos and videos
Do not use cocktail straws because they are easily closed. Material for future beauty should be more flexible! If there are thin tubes, then the products will be more elegant. But it is best to use Scoobid. Consider the stages of work.
Where to begin
In order to make an ordinary bracelet, there is a scheme for which you need to work.
It shows each movement by arrows. This product is performed by two harnesses. The picture shows the first and basic steps that you need to repeat.
Wallpaper № 5 - Tighten the tight tubes, but not much so that they do not break or have broken.
Wallpaper № 6 - the first stitch that will work out. Repeat all actions while the product does not get the desired size. Tip - Apply the bracelet in your hand, so as not to make a mistake with the length of the product.
The accessory of four tubes is a bit more complicated. Consider it attentive:
- Make the nodule, as described above. We take it index and thumb.
- Tubes push on the sides, pulling out. Do not make a product on the weight, put on the table or the board.
- Getting started with green harness. We put it on a yellow loop, yellow - on the blue, creating a loop, blue - on the red, and red finish - a grove in the green loop.
- Pull all the tubes, creating a square.
Multicolored world
Pleting of phenoshek can be made by different nodes, for example, "twisted", "brick", "macrame" and so on.
Such a bracelet was created using a twisted knot.
- Take three tubes of different colors, beads to decorate the product. Bend one of the harnesses, leaving the loop size for the bead. Mix with the other and wind the thread, which is conditionally calling the nodule.
- Forehead flagellas need to be pulled to the required size. Do not forget to ride beads to the nodule tube, withsting gaps. Stretch all the threads through the bead at the end of the product. Gently cut the ends.
Article on the topic: Crochet. 300 patterns of motifs and patterns
How to weave "Brick"
Such a nodule is more difficult than usual, but the products look exquisite and more interesting.
- We apply two flagella perpendicular to the third. The end of the horizontal tube start on the vertical, as shown in the photo.
- I stretch into the loop the end of the left flabby, at that time bends the top down. We carry out under the bottom horizontal tube.
- We repeat the previous steps with the end of the right thread, tightening the nodule. It turns out "brick".
- Follow pictures to fit the product to the end. Be careful with the movement of the tubes, so as not to get confused, mentally mark them with numbers.
If you need to add a new harness in the product, then repeat the following actions:
- Enter the new tube on semi-prepared work, having it diagonally.
- Now we perform two rows with old flavors to secure weaving. Cut the ends of the old tube.
Scoobid - universal tubes. Because they can perform a lot of products. These are not only bracelestics, but also figurines, handles, handbags, photo frames and toys. Basically, one pack of flavors is enough for several works, so we boldly call the needlework rather budget.
Video on the topic
For inspiration with the process, you can see the learning video: