Parakord (from English Parachute Cord, Paracord) is a very light rope, a polymer cord, the fibers of which are made of nylon. Initially, this special type of rope was made for the military and was used for fastening propyl parachutes. In the modern world, the Parakord is used not only at the military, but also in personal intentions: it can often be found at the military, and the amateur hunter. Among men are worthy of products made from this material, so this can serve as a good gift for the birthday's birthday or February 23, and how to soar a brush from Paraconade on their own, you can learn from this article.
The original Parakord is manufactured in the United States. The most popular brand of manufacturer - Rothco. But in reality does not play the slightest role, in which country the product is produced, it is important how much its quality meets world standards. Thanks to the schemes of weaving, you can make not only beautiful decorations, on the example of bracelets, but also learn how to make loops, belts.
We make on the fingers
When you just begin to get acquainted with a weaving from Paracona, immediately in any video lesson or master class will not forget to mention the "fist of the monkey". It is very often used as a decoration - a separate key chain for keys, backpacks and so on. The bowl is usually put a ball. It can be a jump, a metal ball or from an old computer mouse.
In order to evan the "monkey fist" in hand, you will need only 3 meters of Paracona and a ball with a diameter of 20 mm. We weave in turns, the number of which depends on the diameter of our ball. Most often 4.5 or 6 turns are used.
Leaving a little thread on the reserve, we begin to restore our fingers.
We make five revolutions, and the last turn in two lower fingers and twist our weaving, now we are wearing horizontally. In the photo example of 4 turns, we need to do five.
Article on the topic: What do you need to know before sticking the photo wallpaper?
We start the thread through the upper loop, which formed between the ball and the upper fingers. We remove everything from the hands and wrapping the ball 5 times, passing the Paracord in the loop.
We start tightening our design. To do this, pull it gently for the tip of the thread, which you left at the very beginning, and then tighten every loop gradually.
You can find out in more detail in this video master class. It also shows how to weave a beautiful handle. The remaining threads cut and sweep. The original Paracord burns with a smoking flame with a black smoke and smells like a burner plastic.
There are quite beautiful examples as weave the tail of our keyfob.
Weave on the machine
If it is not convenient to weave on your fingers, there are special machines.
For weaving, you will need a Parakord about three meters, a ball with a diameter of 30 mm. Inventory can be bought, but you can do it yourself: it is best to make the machine from the usual area of 5 * 5 cm and four sticks (for example, for sushi).
On the edges you need to make wooden holes and stick sticks. Using this machine, much easier to weave. Also, the main thing is that the turns do not intersect to keep the beautiful pattern.
We take the Parakord and, leaving a little length on the cord, begin to wrench it around the machine. For a ball with a diameter of 30 mm, six revolutions should be made.
Next, we carry out a thread in the middle of the machine. We raise our design slightly up and make six revolutions again, just vertically. It is advisable not to tighten. After you have taken half of the revolutions, you need to insert the ball into the ball and continue to weaven further.
We turn around the column and go inward, begin to rerupt the ball from the bottom. Making 6 turns.
We remove everything from the machine and start to sweep our square, without dragging, so that the sequence of the shoelaces does not come down. We delay from the very first plane on one turn of such a scheme: pulled on one side, turned over and pulled further.
Article on the topic: Cross embroidery scheme: "Horses" free download