For the finishing of facades of buildings today, many different materials are used: decorative brick, siding, ceramic tiles and many other types. Among them are especially popular with facade plaster Coroed. It received its name because the wall, piece by such material, has the appearance of the wood pest. Such facade is always striking, as it has a fairly attractive appearance. The relief can have a different look, it depends on the stucco brand and on the method of applying it. The trim of the facade of the core is not only a beautiful appearance, but also protection of the walls of the walls.
Preparation of walls
Preparation of surfaces for this plaster Coroede includes several stages, so it is a very complex and time-consuming job. After all, training includes not only the alignment of the walls, but insulation and reinforcement. Therefore, this paper needs to take full responsibility, especially when you do it for yourself.
- Alignment of walls. It is necessary, before applying plaster, it is necessary to achieve the most smooth wall (remove all the protrusions, fill the gaps and cracks). The wall must be cleaned of various contaminants and dust. To do this, you can use a rigid brush. To make sure the walls are clean, you can spend your palm. Next, the surface should be projected. The primer is needed in order for small particles of garbage and dust that still have not been removed, they have been fixed, and so that the glue applied in the future had excellent adhesion with the surface. And the primer is used to avoid squeezing plaster.
- Insulation. To create a source of water removal and protect the insulated foam coat, it is necessary to use a metal starting profile from the bottom. It will be the boundary point of our foam. Next, you need to apply glue on the sheets of foam and glue them on the walls. The glue consistency should correspond to the mild clay consistency. The glue must be applied to the wall along the contour of the foam sheet. In addition, the foam itself needs to also apply glue, especially in a leaf center. The insulation must be strongly pressed against the wall so that the stove tightly comes into contact with the wall. The second and subsequent rows need to be glued in the following form: the plates must be put with the displacement of the seams. After the insulating layer on the wall, you need to give glue to dry. For this you need to wait about three days. When glue dries, foam plates need to be fastened with additionally fastener dowels.
- Reinforcement. In order to create a solid base for plaster, you need to create a reinforcing layer. A glue is applied to the surface of the insulation with a wide spatula. The glue layer should not be more than one millimeter. Next, you need to press the reinforcing grid into glue with the help of the same spatula. On top of the grid we apply another layer of glue. It is necessary to glue the grid with a small adhesive of one strip on the other. After the adhesive will dry, it is necessary to apply the primer over it over it.
Article on the topic: Bed height with floor mattress: sleeping standard
Choosing materials
In order to increase the service life of the new decorative plaster Coroede, it is necessary to choose a decent and high-quality material first. Finishing with high-quality materials - a key to success in work.
- Styrofoam. First of all, you need to decide with the insulation. It is best for the insulation of the walls in front of the plaster to use foam. One of the best foam brands for finishing the outer walls are considered C25. The material of this brand is strong enough and it will not break and crumble during the installation, and it will make the facade even stronger. In addition, the foam is much more convenient to work. It corresponds to all criteria for heat saving in the house.
- Reinforcing grid. It is better to use a mesh density from one hundred forty to one hundred sixty grams per square meter.
- Glue. Glue, which is ideal for such works, is a glue on cement-sand-based. Of course, only one that is intended for works with foam. This information can be found in the store from the seller or read its characteristics. The glue is used by the same for foam and for the reinforced grid.
- Plaster. The most important thing is to choose the plaster. After all, it is precisely from its type and structure that the appearance of the building or the walls will depend separately. For the facade, plaster with grain size from three to three and a half millimeters is very often used. It should be understood that the larger the size of the stucco grains, the greater its consumption. What about the color of the material? You can choose the desired color of the material itself or paint the surface of the paint.
Technology Plasters
Wall decoration with plaster is a very difficult lesson, but quite complete. In order not to hire specialists and make all the work independently and at the same time save a lot of money, I will tell you how the walls are trimmed by the core. You will learn everything that your finish does not differ at all from the work of the Master.
IMPORTANT: The plaster of the core is performed entirely relative to one wall. It is so important because if we apply the material on the wall, while sticking out fresh with a dried material, then the connection will be noticeably noticeably.
And if the wall is plastering into one acceptance, then you will have a monolithium of the surface without junctions and drops. The mixture must be stirred in a bucket with a drill with minor turns and mixers. It is necessary to observe the sequence when creating a solution. First of all, you need to pour water and only then fall asleep dry mixture, while stirring.
Article on the topic: Styles of curtains in the interior - Briefly about the main
Water ratio to 1: 3 powder. To achieve good quality solution, the consistency is needed before applying as a potato mashed potatoes. And then give a solution to breed about ten minutes. The last thing to be done before applying to the wall is to thoroughly mix the solution again, while you need to split all lumps. For applying material on the wall it is better to use a hard metal spatula. It is very important to get used to the plastering process. It is important to learn to abide by the layer thickness relative to the grain size of the material.
If the depressions appear on the surface, it means that you do everything right, that is, you put a layer right. When the layer is already applied, but not yet dry, it is necessary using a plastic grater and rotational movements to create a preliminary surface texture. The final layer is created after some time (10-15 minutes). The core will dry and will not stick to the grater. It is best to work in a pair: the first person is engaged in applying plaster on the wall and will stretch it. And the second person, lagging behind the first to 15 minutes, is engaged in the final view. The most recent action is applied to the surface of a protective acrylic varnish. It can be both matte and glossy and has many colors. Before applying varnish, you need to give the day the facade dry and then apply a primer, and on the primer - varnish.
If you decide to use a cored as a finishing material for external walls, then this is a good choice. The facade of the building, decorated with this material, not only attractive, but will also save walls over long and carefree years.
Video "Application of the plaster Coroede on the facade of the building"
The record shows how to qualitatively apply decorative plaster "Coroed".