According to statistics, at forty-one percent of residents in our country there is a dog. This percentage exceeds from domestic animals of cats. And this is normal, because the dog requires more strength, time and finance from the owners, unlike other pets. An ordinary peel is necessarily necessary a set consisting of a collar and a leash. It is very sad that even such a small part of the necessary inventory is growing every year. But you can save a bit and at the same time have several sets of this inventory for any reason. Now we will analyze how to create a leash for dogs with their own hands.
We start with classics
Now we will look at how to sew a classic leash option.
For one and a half meter option, it will be necessary:
- nylon or tarpaulin tape two or two and two and a half centimeters wide, and a length of 180 centimeters;
- Durable carbine with a latch;
- For the design of the jacquard ribbon, about three meters;
- sewing machine;
- a thread;
- scissors.
We take the carabiner and insert the end of the tape into the ear in the eye, wrap it inside. It turns out a bending of three layers, it must be fluffled with a sewing machine around the perimeter, and then another cross-cross. In any case, we perform fixing seams.
From the second end of the ribbon we sew a handle. To do this, turn the hand with a ribbon and add three or four centimeters for comfort. Now we flash the ribbon with a bending, and the loop will turn out.
We take jacquard ribbon, fold it in the middle and cut. We apply both parts of the ribbon to the base of the leash, while closing the seam next to the carbine and loop. Fresh ribbon with a pin, then flashing on the machine. Here is a pretty classic leash.
Interesting option
A leash made from Paraconed will be an excellent leash option - this is a very durable and durable braided leash, which is well suited for any breed of dogs, regardless of their size.
Article on the topic: Plastic bottle pig: Step-by-step instruction with video
To make a leash from the classic "Cobra" knot, you need about thirty cord centimeters to get a piece of leash in two and a half centimeters, not counting the middle. For thirty centimeters, the leash will be required to be fourteen more cord. Based on this, it takes about four hundred twenty centimeters of the lace, of which three hundred sixty centimeters for weaving and sixty centimeters for the middle.
In working with this material you need experience, so do not be discouraged if it turns out not immediately perfect. If you make such a leash for the first time, it is better to buy it more than the calculated size.
If you choose "Royal Cobra", then the cord consumption will already be 45 centimeters by 2.5 centimeters of the leash. Sometimes the exact amount of material is not possible, so it is better to take a lace with a margin. In this master class, a leash of 180 centimeters was created, and approximately 480 cord centimeters took place, including 45 centimeters per hand. A total of 525 cord centimeters was spent.
Now let's look in detail the node. At first, you need to find the center, it will affect the length of the leash, the knot and distance to the carbine. Now we take one of the ends of the lace, put it on the center, leaving the loop. Now we take the second end and spend it over the 1st, but this time under the center and stretch the lace up through the loop. We continue to do the same, while directing the cord in different directions, and when using the "Royal Cobra" method, we do the usual twice, and we use it as a center - this will give more strength and volume.
To create a leash will be required:
- scissors;
- Roulette or centimeter tape;
- Parakord;
- lighter;
- clamp;
- rubber;
- carbine;
- small cut of an old lace;
- Time, strength and description of the work.
Make the right knot on the carbine.
Article on the topic: Applique "Snowman" with paper templates and cotton disks
The clamp is wide, so it is necessary to wind up a loop several times, and only then stretch the lace through it. Make the main nodule, winding and stretching once. But if necessary, you turn it off yet. In this case, it turns out a strong not moving connection. To keep the carbine, we take the old lace and tie it using the prusik nodule:
And now it is time for the most curious part of the weaving is to create a handle. If you figure it out with the method of its manufacture, everything else will immediately become very simple. After we attached the lace to the Carabin and measured the desired length, you need to make a loop of a parached cord of the loop - it will handle. Then we make a "jump in the middle", for this we take 2 intertwined cords and begin to intertwine them through the bottom, where the loop is connected to the leash. Here will be the mount of the handle.
For the "jump" we bind the handle using Cobru. And finish using the "Royal Cobra". So that it was more comfortable, make a motel lace and secure it with rubber bands. Thus, it will be more convenient to stretch it into the nodules, while not stretching the entire length of the leash, and also keeps a lot of time and effort.
When the handle of the handle is completed, it will be necessary to overtake the original center. Once again, we make a "jump" along a long piece and make a continuous loop.
Now you need to leave the entire lace from top to bottom. A neat appearance is important here. It will be good if we are wearing as close as possible to the climax, so the leash will become wider. The meaning in the fulfillment of the reverse "royal cobra".
When we collapse as much as possible at the clamp, you need to turn everything and make a "cobra" as the middle. At the same time it is necessary to keep closer to the climax, so that the leash in the future is not twisted and did not turn. Remember that the turn should be placed in the opposite direction.
Article on the topic: Holder for napkins do it yourself
Having reached the starting point of the handle, taking it in a circle.
When we reach the long part before the long part, we cut and we melt the lace, now I pull it with pleasure and cut off unnecessary, after you are convinced that the lace edge is firmly fixed. And here is a great and interesting leash is ready and a host can also be delighted and a pet.
This version of the leash will be more strict, it is created from the belt tape, about two and a half meters long. To do this, we melt the edge with the help of a lighter, then we produce an end to a metal ring, creating a handle and attaching a strong seam. Now you only need to hide the carabas on the ring, and the leash is ready.
Video on the topic
There are other methods and options for creating a good and unusual leash for your favorite pet, so a few more video is presented below.