To make the transformer table with your own hands, it will take a tree, plastic or metal. Pre-prepared drawing.
Drawing table-transformer.
Preparatory work
How to make a table of wood, professionals know. They recommend doing a table top of 1-1 / 2 inch wooden board either plywood. The choice of material depends on the load that will be displayed on the transformer table. The feet of the table are made of a bar with a cross section of 20x45 mm. The transformer table is made with their own hands using a screwdriver, saws on a tree, fastening elements, sandpaper, simulators, brushes and varnish.
From a constructive point of view, the manufactured product should consist of a tabletop, a frame with rigidity and legs. Billets are made with the prepared drawing. The legs of the transformer table are cut at an angle (for stability). To make a folding tabletop, you will need to find it middle. The product is cut into 2 equal parts. On each half, the support tires for the legs are placed (indentation from the edge should be 5 cm). Halves of countertops are fixed with a loop. Spiles are processed by the edge. The loops are fixed to the top of the legs. The table itself is assembled using metal fasteners and special glue.
Mounting books on a tabletop feet.
To make a table type transformer table, you will need to decide on its size. The optimal option is considered:
- height of 750 mm;
- width of 800 mm;
- The length of folded design is 282 mm.
The constituent elements of this table include:
- the basis with rigidity ribs;
- 3 parts of the table top;
- 2 legs of sliding type.
If you wish, you can make 2 tables of this type. For its manufacture, drill, screwdriver, LDSP (3500x1750x16 mm), corners, configmatics (75x4.5 mm), edge, self-tapping screws are required.
Primary production
LDSP can be cut into the workshop. It is not recommended to produce this process independently in the absence of due experience and knowledge. The future Table Transformer provides for the manufacture of the following composite elements (mm):
- 2 covers (800x635);
- Little cover (800x250);
- 2 racks (734x250);
- 3 rigidity ribs for the base (708x110);
- 2 ribs in retractable legs (568x180);
- 4 racks (702x60);
- 4 planks (600x60).
Article on the topic: Features of the office of an advertising agency
Scheme of laying table-transformer.
Previously, the components of the constituent elements are seeded by a melamine edge. This will require iron. On the end put the edge, pressing the hot iron. Excess adhesives are cut off with a knife. The legs are collected by Eurovints. The latter elements screw the loops. The next stage provides for the assembly of the base of the table. The horizontal bottom edge must be fixed at a height of 100 mm from the floor level. At the same time make an indentation from the edges of the sidewalls in 70 mm. The next edge is installed on the previous analog. The upper edge should be between the previous element and the table top.
The base is installed on a small table top upside down. The sidewalks are placed deep into the table, observing the indentation from the edge of 3 cm. On 2 sides of the base lay 2 large covers. The elements are collected, the caps are screwed using loops-butterflies. The next stage provides for the screw of the transformer table legs. The product is ready to use.
Folded construction
If necessary, you can make a transformer folding table. In the folded form, its length will be 90 cm, and the width is 18 cm. From a constructive point of view, such furniture consists of a tabletop, supporting support, 2 ducts and shelves. For its manufacture, the LDSP is used with a thickness of 16 mm, the boards either glued to the fan. Parameters details are following (mm):
- 2 pierces (345x345);
- Countertop (450x900);
- Shelf (150x900);
- Bearing support (900x620).
To make such a table with your own hands, the piano loops, self-tapping screws, DVP will be required. Prealt the ends of the laminated chipboard with melamine edge. To close the rear surface of the carrier support, the Fiberboard will be required.
This material will hide the place of fixation and gaps formed between furniture and wall. The pumps are connected to the side internal ends with the help of piano loops. To the back screwed brackets. To fasten the shelf to the main design, the screws will be required. They must accurately enter the end of the niche. The countertop is hung at the expense of piano loops. Hooks fixed to the wall.
From the floor level until the countertop should be a distance of 700 mm.
This parameter depends on the personal preferences of each person. The resulting table is easily dismantled and installed with your own hands in any room.
Article on the topic: Curtains for the kitchen - an interior raisin