Bar and boards are common materials used in the construction of houses. In the absence of funds on finished materials, they can be made independently using chainsaws. Before cutting the log on the boards with their own hands, it is worth learn more about the features of this process.
Advantage of a chainsaw log saw
Cutting on the boards can be carried out using the tools such as electrical chainsaw and additional devices designed to simplify operation. During the choice of certain products, it is necessary to focus on the amount of alleged work. Stationary sawmills are distinguished by high cost and are purchased only if it is planned to organize business to create boards.
The most affordable tool for work is chainsaw. Such devices have several advantages over electrical:
- chainsaw can use anywhere, regardless of the availability of the power grid;
- The tool is suitable for working in conditions of high humidity;
- Professional chainsaws significantly exceed electric power;
- You can use chainsaws continuously for an hour.
For sawing logs on the boards together with a chainsaw, a special frame is used, which is fixed on the device and allows you to create one thickness boards. It is also necessary to fix a log to the log in one position. In addition, the guide will be required.
Since household gasoline saws are not designed for a larger load, for sawing logs it is worth using professional tools. When choosing, you should pay attention to devices, with a capacity of more than 7 horsepower. Before work, the fixed frame is adjusted in accordance with the selected width of the boards. To create a frame, you can use the legs from the school desk or metal corners.
Types of workers' nozzles
The choice of nozzles for work depends on the volume and type of work. The following devices are applied with chainsaw:- Drum Debarker, which is necessary for removal from logs of a bark;
- Lightweight nozzle for sawing logs;
- Standard nozzle used to create boards.
Article on the topic: Independent installation of rolled curtains on plastic windows
Nozzle for longitudinal sawing
When using such nozzles, sawing occurs in a horizontal direction. It is fixed on the tire using special clamps and allows you to create boards of equal thickness. After the work, the boards are dried, and then can be used during construction.
Lightweight nozzle
Such devices are used often, but they should be applied only in the case when boards for fences or sheds are created. This is due to the fact that the fastening of the tire nozzle occurs only on the one hand.
Podanist
Nozzle for removing the bark with logs is used at the expense of clinical transmission. Attachment occurs with belts - for this, special pulleys are applied. It is worth noting that the workability of the nozzle can be changed, since the speed of rotation of the shaft depends on the size of the pulleys.
Features of saw cutting when using chainsaws
Create additional equipment for sawing logs simple enough:
- To create support, a frame is used, which can be created from the legs of the school desk. The most suitable are pipes with a square cross section of 20 × 20 mm.
- When building a frame, it is necessary to create 2 clamps, and on one end fasten the cross. On this element should be holes for tie bolts. The middle creates a protrusion for the tire.
- In order to cut the log along, it is necessary to construct the support frame, the width of which should be no less than a length of 8 cm.
- For the convenience of work, the handle must be welded on the frame.
- Before working, it is necessary to carefully check whether the frame on the tire is securely secured.
Use the homemade tool is simple enough. Before sawing, you need to install 2 goats - they will be used as a log support. In addition, a metal rack or a flat board is prepared, which will serve as a guide element.
Sawing technique along
The most difficult stage of the process is to make the first speaker. For this you need:- Install the master ruler, which consists of two boards, which are bonded between themselves at an angle of 90 degrees;
- After that, it is necessary to place the sawn log on the supports and fix it;
- Then it is important to check if the log is smoothly located;
- At the next stage, it is necessary to secure the leading ruler on the supports using self-tapping screws;
- After that, you can start creating the first sleeve.
Article on the topic: Curtains from patchworks do it yourself: Technique Patchwork
Features of transverse breakdown
Transverse cuts applied only to create wood or interior elements. Working is carried out in several principles:
- The log in front of the work is located in a horizontal position on the supports. The height of its location should be 0.5 m.
- After that, it is necessary to completely clean the log from the crust.
- At the next stage, it is necessary to make a label on the whole log, located from each other at an equal distance.
- Then, on the created marks, you can carry out sawing.
For transverse cuts, specialized devices are not required.
Security rules for work
To avoid injury, it is necessary to comply with the basic recommendations:
- Before using the benzoinstrument, you must carefully read the instruction that is included.
- Since the chainsaw is a dangerous tool, work should not be able to intoxicate or during illness.
- Keep the saw you need both hands. Reliable grip will allow you to control the movement of the instrument and maintain its position with unexpected jerks and in case of recoil.
- In arms during operation there should be no fuel mixture or oil, as it reduces the reliability of grip.
- It is unacceptable to use a saw in case it is damaged, not fully assembled or not adjusted.
- During work on the site there should be no children or animals.
- In the absence of special skills, you should not use chainsaw on the stairs and other unstable surfaces.
- Do not make a sawing on the elongated hands and above the shoulder level.
Subject to the described rules, the risk of injury is significantly reduced.