Toiletz is a complex plumbing design, which is a necessary element in any apartment. To collect it, you need to prepare a place to install, bring water and only after that start the assembly of all nodes. The drain blade of the toilet bowl is intended for a set of water and for flushing the waste of human life in the sewer system. The inner part of the tank mechanism for the toilet bowl, which consists of the float and drain device, should always be in good condition.
Diagram of the device of the drain mechanism of the toilet.
Its proper adjustment prevents water overrun, which leads to unnecessary consumption of money.
How the worn tank is arranged and adjusting its mechanisms
After installing the toilet bowl and connect it to the plumbing pipe, it is necessary to check that all compounds are sealed, the liquid is gained to the desired level and merged from the tank completely or half the capacity. All this can be achieved by adjusting the drain mechanism in the toilet. Before proceeding with this process, it is necessary to figure out in detail what the drain unit of the toilet is consisting of. Adjustment of the drain mechanism is performed using such tools and materials as:
- adjustable key;
- pliers;
- Fumelight;
- wire;
- rubber gasket;
- Sealant.
Diagram of the device of a drain tank toilet bowl.
Currently, many different modifications of toilet bowls and tanks have been created for them, however, the principle of operation of the internal mechanism is the same. The basis of the drain device of all modifications includes a device for draining water and shut-off armature, which consists of an inlet valve and the float. The water supply device is attached to the hole, which is located with the right or left side of the barrel from above. From the inside, a rubber gasket is installed for fastening the valve, and a plastic nut is tightened from the outside.
When a liquid flows through the valve, the float floats and at the desired level, the lever presses on the plastic plug on which there is a rubber gasket. It in turn closes the water supply nozzle. In order not to be overflow, the float can be adjusted. For this, its lever must be bent so that the fluid is slightly below the drain pipe. If the lever is made of plastic, it is provided to be adjusted using a ratchet or fastening screw.
Article on the topic: how to install rollers on plastic windows
In some flushed tanks, water is constantly flowing into the sewage system through the drain pipe and cannot get to the desired level, naturally, and the float cannot rise to the necessary height. This is happening when the sealant was slightly worn out, and because of this hemetization was disturbed. You can eliminate such a malfunction using a simple device - a small cargo, such as nuts.
Scheme of the drain mechanism 3/6 l for a toilet bowl.
It is not difficult to assemble such a design. For this, the Georg is hanging over the outlet on the pear or lever. Such a device helps to achieve not only tightness, but they can also adjust the drain process. When the valve rises using the button or lever, the fluid begins to merge into the toilet, and low pressure is formed in the pipe at this time, and, despite the strong subference, using the weight of the fluid at any time.
The water level can be adjusted using the overflow pipe. It is exhibited so that its upper edge is located just above the level of water, the float will be able to overlap the valve of its receipt. Sometimes in it, due to any defect, the fluid is recruited, and it cannot perform its function, so in this case the float must be replaced.
Method of adjusting the water level in a flip of the old sample
Simple drain tank design scheme.
In newer models of this plumbing equipment, it is not necessary to carry out the toilet bowls, since the drain of the fluid is already adjusted by the Division. In modern tanks there are two buttons for draining. One serves to complete the release of water into the sewer, and when the second button is pressed, only half of the tank volume is consumed.
On old models, whose tanks are highly suspended, the side lever when dragging the water captures the bell behind the eye and because of this, in the process of work, it can be brought or clamping a hinge. In order for such a flux device clearly, the hinge between the lever and the button is fixed using several turns of the wire. This method is manufactured by a device in the form of a fixed lever between the drain mechanism and the riser. With this device, you can adjust the drainage of fluid in the toilet, which is important for the economical flow of water.
Article on the topic: How to fix the bath?
Using all these simple devices, adjust the worn tank so that the toilease worked properly and economically.