A practical and convenient acquisition for the bathroom will be the cabinet under the sink. It is easy to install it with your own hands, but it should be carefully choosing its location in the bathroom. The cabinet should not interfere with opening the doors to the bathroom, overlap the passage to the washing machine or block the shower doors. It should be placed with such a calculation so that later it was possible to hang a mirror, a towel hanger or a locker, so it is not necessary to place an end to the walls with low-laid pipes or under the windows.
In addition to the fact that the cabinet is very functional, it hides and communications.
The most common variant of the material for the cabinet in the bathroom is a tree. Choosing a wooden tube, make sure that it is laminated with special moisture-resistant coatings or veneer covered with moisture-resistant varnish. It is important to pay attention to the material from which the sink stand is made. Although the marble countertop looks great, a much more practical moisture-resistant stand from tempered glass or acrylic is suitable for the bathroom.
Assembly and installation of the cabinets under the sink do it yourself
The standard package includes: bottom, two side walls, two doors, two jumpers, fittings, decorative facade, legs (depending on the design of the cabinets there are four or two).
Set for self-assembly: 2 doors, 2 sidewalls, decorative under the sink, donyshko, 2 jumpers, 4 legs.
The purchase scheme is attached to the purchase. If necessary, holes for hot and cold water pipes are cut in the bottom and side walls. Then, according to the scheme, an assembly of the carcass (without doors) is built. Handles are put on the doors, but because they themselves are mounted last time, while the doors can be postponed. If the nightstand arrived home already in the assembled form, then the door, respectively, are removed.
For mounting the cabinet, the following tools will be needed:
- Perforator;
- dowels;
- building level;
- putty knife;
- Malyary Scotch, Silicone.
Article on the topic: Wallpaper with ornament: Interior ideas
The cabinet is set with such a calculation so that the side walls are symmetrically relative to the sewer output. The height of the cabinet is regulated by means of twisted legs. The accuracy of the installation is checked by the construction level. After that, the fastenings and the cabinet are drilled through the bottom and top bar.
Before using silicone, the place of the future seam is punctured by a painting ribbon.
Then the sink is installed in the cut-out tabletop and is attached to the wall, or with the help of anchor screws, or is glued with silicone. The second method is preferable if the wall is very thin, or I do not want to double the tile, or the fastenings are not provided in the sink itself. Before the silicone pouring, the sink at the junction with the wall along the contour is placed by a wide strip of the painting scotch, so that the tape visits not only to the sink itself, but also on the wall.
Then, slightly pulling out the washbasin on itself, the joint between the sink and the wall is powered by silicone. After that, the sink is tightly pressed against the wall, silicone is spacing with a spatula and remove the tape. The day will be waited until silicone dries off, the siphon and the mixer are assembled, the decorative facade is glued, the shelves and doors are installed.
Simple and comfortable bedside table with your own hands
It may happen that under the sink does not fit any purchased shopping bag, it is impossible or it is very difficult to choose something suitable in size and color, and the prices bite. But there is always a yield, and in this case it is a cabinet under the sink with your own hands. It is made of chipboard or MDF plates with a thickness of a sheet of 16 mm. For the same purposes, the old disassembled wooden furniture is quite suitable.
To make your own handmps, you will need:
The base of the cabinet height is 12 cm has the appearance of the hollow sealed box from the OSB.
- electric jigsaw;
- Self-tapping screws with a rare thread pitch, they are black, yellow, white, selected by the color of the material;
- Furniture corners (four pieces under the tabletop and two on the shelf);
- sandpaper;
- Putty for wood, primer, paint or varnish, brushes.
Article on the topic: Light filters on the windows from the bottom up or "upside down"
It should be pre-conducting all the necessary measurements and draw a sketch of the future product. The standard sizes of the sink of the sink are 40 cm in depth, 60 to the depth and 70 in height, but may vary depending on the dimensions of the bathroom, the size of the washbasin and your own preferences. Before making the manufacture of stands with your own hands, you should decide whether you want to attach the legs to it. In this case, they are acquired additionally. It is better to choose decorative chromed, they will serve longer. The approximate height of the legs is 10 mm.
In accordance with the calculated sizes of the couch, on the wood plates are placed and cut out the logs, bottom, doors, jumpers and shelves. Special attention should be paid to the cutting for the sink bowl on the tabletop of the couch. The walls and the bottom are collected and fastened with the help of self-tapping screws, the door loops are attached on them and, if planned, legs. After that, the finished frame is set to the place of the future placement of the cabinet, its height, dimensions and stability are checked again. If everything is fine, the top stand is attached to the top stand from the bottom of the short self-tapping screw. Tumba, collected by her own hands, is practically ready.
It remains only to sharpen and process the surfaces with sandpaper, then apply primer. Then the end made by your own hands can be painted or just covered with transparent varnish. A hand-made cabinet under the sink is mounted as well as purchased. Door hinges are installed. Shelves are attached with furniture corners.