What you need to take if the interroom does not open, slammed, broke it or was locked from the inside? If the locking mechanism is not broken, but just closed, there is always the opportunity to open the door with the key, of course, if it is not closed in that room, to get into which it is necessary. It is necessary to consider the most common situations and basic ways to answer the question: how to open the handle of the interior door without a key?
Interior door handle design.
What could be the cause of slamming interior doors?
First of all, it is necessary to identify the reason why the interroom door does not open. Often the reason can be the following events:- The castle, located in the door handle, jammed, or it is completely broken;
- Latch, locking door, shifted;
- The tongue of the locking mechanism jammed;
- From the opposite side, a key is left in the well that does not allow it to turn it off.
In order for the reason to be detected most accurately, you need to raise the door cloth in different places with a wide screwdriver. Having tried to pull the raised canvas, you can determine which specifically the place it is held. After the reason is detected, a particular image of action should be elected.
The problem consists in the latch
Tools for working with door handles.
The most frequent problem of locking mechanisms for interior doors is precisely in the latch. This design detail may not be screwed to the end. With full pressing on the door handle, it still continues to stick out from the face of the product. Thus, if the door is well pressed into the frame or push it with force, it is possible to drive this very latch into the groove of the door frame so that the most sticking part of it will not allow the design to reveal again. Even if the door handle is unscrewed, it is round or lowered until it stops. These few millimeters of this detail will be able to firmly strengthen the canvas in the box without allowing it to open.
Article on the topic: 3 ways to make a comfortable father-in-law with your own hands
In this situation, you need to press the door leaf from the box with a screwdriver or other rigid items, simply raising it.
Problems with the tongue of the castle
The situation may occur if the door was not closed on the key. Her locking mechanism is not equipped with a latch, but it still does not open, although the door handle is omitted or scrolled (if the knob is round) until it stops. The reason for this may be incorrect operation of the design. In order to solve a similar problem, you will need a thin flat tool that must calmly go into a small gap between the interior door and its box.
Door handle lock mounting circuit.
In addition, the tool must certainly have the necessary level of strength, because, breaking something in this slit, you can only aggravate the situation. Screwdriver, plastic card, ruler or ordinary knife can act as such a tool.
Step-by-step instructions will allow each person to open a mechanism that has crossed the tongue:
- Plastic card, ruler, stationery or ordinary knife must be inserted between the door flap and the box in the area where the jammed part of the design is located (you should navigate the area where the door handle is located).
- The tool should be tilted a little and press. The master should feel how the tool elected tool slides, in contact with the beveled tongue.
- The tool should be sent towards the door sash, allowing the tongue to completely disappear in the lock. During the production of these actions, the door handle should be kept in lowered, and the sash to pull into the one way to which it opens.
The situation will be more difficult if the master is from the other side where the tongue does not have a bevelled surface. In this situation, you should use the same tool. Only insert it is necessary on top and try to influence them to influence the inner bevel of the castle to push the tongue. Smekalki and forces in order to cope with such a situation, it will be necessary much more.
Article on the topic: Ideas for crafts from autumn colors (56 photos)
Door lock fault
Handle height for doors.
The situation where the malfunction of the castle itself was the reason for the impossibility of opening the interior door, it is necessary to solve by influencing the locking mechanism.
If an English lock is standing in the slammed door, then half the case has already been done, and everything else does not take a lot of strength. The cylindrical mechanism of such a lock can be neutralized by drilling it using a normal drill. Having got rid of the damned larva of the castle itself, it is enough to pick up the preliminary mechanism in such a way that the locking reigleel is drawn into the castle. The problem is solved. However, the lock or the larva must be replaced.
In addition, the cylinder of such a castle can simply knock out, supervised it is a rather solid object suitable in dimensions. To knock out, you must use the usual hammer or what will be at hand.
If the lock is not used for locking, then the problem will be solved much more difficult. First of all, it is necessary to inspect the handle. If it is attached by bolts, they need to be unscrewed using an appropriate screwdriver or other well-tool tool.
Door handle installation circuit on square base.
After the handle is removed with a thin metal bar, a pencil or a different thin durable item, you should try to find the part of the mechanism that is responsible for snaging, and try to click on it. At this time, the door handle must be lowered until the stop. At the same time, pressing the door towards the opening of the canvas.
If the whole problem lies not in the latch, but in the fact that the locking reigleel jammed, then it will be very difficult to cope without the help of a professional.
The key remaining in the castle from the opposite side of the door
Such a situation is often a problem. People accidentally lock each other, or small children can close in the room and do not know how the castle unlocks.
Article on the topic: Subtleties of installation of shower pallets
Solving such a situation often does not carry any devastating actions for no lock or for the door canvase. The way to solve this problem is easy and familiar to many who have already come across closed interroom castles.
First you need to slip under the canvas paper or fabric.
Installation scheme of double-sided door handles.
With the help of the knitting, fine twist or wire, you can try to push the key, which is located in the opposite part of the mechanism. When the key is finally pushed out, it just falls on the fabric or paper cloth under the previously sublated, with which it can be dragged to the other side.
This method is applicable only in the situation if the design of the locking mechanism is provided for the presence of a key well in both planes of the interior door, and only with this condition that the key from the opposite side is not scrolling.
Secrets of interroom castle
Modern manufacturers, knowing about slamming problems, also did not remain aside. It was invented quite simple, but the successful design of the door lock. Such a lock is endowed with a keyhole on the one hand, and on the other hand, it is a specialized button, which is pressed completely blocks the movement of the lock, thereby locking the design.
For cases when in closing there is no need or design, it is necessary to urgently unlock, from the opposite side there is a hole, leaking into which something thin and durable, for example, the needle, you can open the door.
In that situation, unless any method allowed to achieve the desired goal, the glass in the interior door can be removed, carefully removing the fixing rails.
In an exceptional situation, the decorative insert of glass can be broken down and, having access to both parts of the lock design, open the door canvas. True, after such a discovery, the canvas will have to change or, at a minimum, replace the broken glass.