Interior doors are implemented by shops without hinges that are supplied complete, so make the right choice of the product of the corresponding dimensions is required simultaneously with the choice of suitable loops. Installation of invoice canopies will be one of the most suitable methods of mounting loops. To properly install the loops on interior doors, you need to choose optimally suitable places, marking them where loops will be located.
To install interroom doors, the card loop is most often used.
Installation of loops depending on the weight of the interior door
The use of card loops when installing interroom doors in our country is the most popular. Card loops consist of two plates, called wings or cards, in which there are special holes, through which products are fastened with self-drawing to the door.
The choice of loops depends on the size and weight of the door.
Russian production of this type of loops is debugged from Soviet times. This type of product is rather ordinary, although its size is completely different. This type of loops is no longer used when installing interroom doors, since they are well suited for street fences or premises that are not residential.
In five-way products there are 5 holes for self-tapping screws on each of the cards, and in four-link - 4 holes, so they wear such a name in the people like four and five. Select the required product of a particular size is required taking into account the weight of the door. Heavier doors are hung on large loops, and lighter - on those that are smaller. For very heavy, the use of three loops is suitable, as for the lungs, which will put their operational properties at the level above.
How to properly and carefully make marking for cutting holes for loops
Marking for loops with dimensions.
Make a marking for fastening loops in two ways. The first is associated with the applied loop to the doorway, with its subsequent stroke of the pencil. Typically, the doors are strengthened due to the two products that are located at the bottom and at the top, and the distance between them should be the same.
When installing the third loop, it can be placed in the center or shift up. Before installation, special marks are made using a pencil that is well sharpened. This can be done not only on the door frame, but also on the door canvase. It is possible to make the marks in the second way above and below, retreating from the edge of the canvas at 15 - 25 cm. After that, the places of fasteners mark.
Article on the topic: Plastic Plinth for Bath - Mounting Secrets
When marking places of holes, it is impossible to be confused, where the door has the bottom, and where the top, considering how it will stand after its mounting to the hinges. If you have glasses, the door should pay special attention to their location.
In this case, the edge of the loops is combined with the edge of the door canvase. If the fittings are counted, then the execution of seats must be carried out with marginal accuracy and accuracy, as it is impossible to allow distortion by installing the mechanism.
Marking under the loop can be carried out by attaching it to the door canvase, and put in a pencil.
When the door frame is assembled, and all the necessary sizes are made, then go to the installation of the loops where they are scheduled. Products should be placed to those places where they are strengthened by marks, it will give the opportunity to imagine how they will look.
The location of the loop will be similar to the first option in the absence of certain differences from the new interior door. All sizes are determined only when the interroom door was examined visually. Installation of loops on the door frame and the door canvas is made taking into account the direction of opening the doors.
Correct product selection and creation creation for wooden doors
Options for installing a different number of loops.
Before buying a loop, it should be found out what kind of loops will be needed, that is right or left. To do this, it is required to get up near the opening where it is necessary to mount the interroom door. The main thing is that it opens up at the same time. It is important not to confuse the parties and not stand so that the door opens from itself, which is not correct.
Open the door is required for yourself, which will mean that which way it opens is left or right. If on the left, then you will need to make the choice of left loops, and if on the right, then right. It is elementary to understand, it is important to correctly determine the type of the required product.
Choosing this type of products for fixing interroom doors, it is important not to confuse them among themselves, noting all the corresponding places of fastening, that is, where and which loop should be attached.
If the door is made of wood, then it should be cut with the contour loops of the wood layer from the door frame using a sharp knife. Making a thin cut, one should take into account what thickness is available at the loops. For a more convenient cutting of the cut in the wood, the corresponding cut vertical is made taking into account the contour of the product. If only the horizontal cut is made, then this can cause a separation of unnecessary areas of the wooden door of the canvas.
Article on the topic: Shower cabin without roof
After performing the markup, the section is performed by a chisel or or a special typewriter.
Similarly, the creation of a cut on the canvas is carried out. If, when creating grooves, use the chisel, then this will lead to the fact that the canvas will be corrupted.
The execution of this work using the chisel is not possible, since it will take a lot of time, and the hole itself will not look carefully. If the necessary groove is already made in the appropriate part, it is conveniently cut with a chisel. If you have a bitch on the web, the loop is shifted, which is nothing terrible.
By making a choice of loops, you should remember that you may need to disassemble if you need to make furniture in the house. And remove the sash can be too complex procedure. To remove interior doors, you may need to dismantle the right or left side of the door.
How to carry out the installation of the loops on interior doors correctly
To dismantle and install the loops, you will need the following types of tools that will help facilitate all the work:
The correct montage of the loop is when the loop enters exactly in the groove, the drawdown is allowed 0.1-0.5 mm.
- Screwdriver.
- Drill.
- Cutter.
- Thin drills.
- Awl.
For the installation of mortise loops, a small circulation saw can be useful, be sure to have a pencil or marker at hand. Before installing the loops, the canopies are disconnected. The larger part of the canopy must be installed in the box, and the smaller - in the door canvas.
The high accuracy of the installation will be provided if you put the door cloth to the door box, which will make it possible to trace the coincidence of the marks made for the purpose of the loops. It is very important to check for various deviations, because even with a small error there may be a situation at which the interroom door will open and close in itself, which will not be pleasant for the owners.
Applying the loops to the inside of the canvas, you need to monitor where the hinges are. They must be addressed to the front side, that is, where the interroom will open.
How to apply fasteners in the process of mounting the loops
Diagram of the device and fasteners of the loop.
Next, you should fix the parts with the help of self-samples supplied in one set with hinges. Before screwing the fasteners, you should combine holes and tags for them, which will prevent the tree splitting during screwing the screws.
Article on the topic: How to build a pigsty yourself
If you need a knock-off hinge for interior doors, you will need to perform more complex procedures than when the conventional insertion. Secontane accessories for doors requires preliminary preparation of deep seating. A hole is cut on its exact contour. Gently using a milling machine.
One of the solutions to the problem of proper cutting loops is the use of mechanized tools, which requires certain skills when working with them. Cutting loops begin after preparation of all tools and make the markup of the door leaf and the door box.
Connecting loops with screws, be sure to ensure that the loop does not go away. Screws always twist exactly in the center by making special labels in the form of pencil points, and then placing them with a seboard. This will prevent an excessive mud hinge with screws in the tightening process.
If the door loops are embarrassed correctly, then they must be located at one level. If the loop is detected, then you must not be lazy, deepen the platform to the required level, but not more. Then, using the line, it is necessary to check the accuracy of the loop fit.
If the hinge is pressed, then after installation, a large gap between the door frame and the canvas is formed. Correctly installed internal loops, you can ensure the opening of the sash at an angle of 180 °. The load that doors can withstand should be not more than 50 kg.
After that, insert the components of each loop between themselves. With independent execution of this operation, the door leaf is lifted to make it possible to determine the point of combining canopies. Each bolt is then inserted into the desired hole with a free hand after installing the composite levers in the desired plane.
This mounting stage is the most difficult, then adjust the location of the door leaf, correlating it with the louting. As a result, the same gaps are obtained between the magnifier and the sash throughout the perimeter. The entire routing process should be performed extremely gently and carefully.
If there is a situation associated with the choice of loops for interior doors, it is better to choose hidden canopies.
You should match the hinges while holding the door in the doorway. After leveling, the loops begin to insert loops pins, for which you need an assistant.
Next, check the doors for an even move, and the latch is connected on the door jamb along with the locking plate. If necessary, it is moved if it starts to make noise when closing the door, then the metal tab is slightly adjusted.