Photo
There are several ways, according to which the wall decoration can be performed. The panels can be positioned vertically or horizontally. Before considering the procedure for performing the work, you need to know which laminate is suitable for mounting on the walls and in what rooms you can perform a similar finish.
Laminate laying scheme with their own hands.
What laminate can be used?
Split adhesive, tongue and clicking laminate. Adhesive laminate has smooth edges. Such panels are devoid of locks. It can be laid on smooth surfaces. For consolidation, construction silicone and liquid nails are used. Installation is extremely simple: the glue is applied with a zigzag on the wrong side of the panel, it is stacked, then the end of the panel is processed by glue, the next and so to the end is stacked. Speaking excess glue you need to immediately remove with a wet rag. The decoration of walls with laminate of this species is impossible, it is only suitable for floors.
Castles on a tongue and cliking laminates.
The tongue laminate is equipped with a special lock. It also stacked with glue. The spool is not sick. As a result, the joints are always accurate and dry. The bands are fixed into the groove of the tongue with small nails or whip-clearing brackets. The wall decoration can be made in such a laminate.
Clicking laminate is a more advanced version of the tongue. The crest of such panels in the context has a pear-like shape. When laying this material, the adjacent panel leans approximately 20 degrees. The castle crest is introduced into the groove, the pressure is rotated to the base, as a result of which the lock is snapped. The walls of the walls made by such panels differ in very high strength. In addition to glue, small nails are used to attach such panels. Kleimers are not used, because The lock will not snap. The decoration of the walls is performed exclusively using glue and on a wooden crate.
Article on the topic: Photothel and photos: what to pay attention to when buying
Often the laminate is called MDF panels that have the appropriate size. It is a very high-quality material with excellent performance, but it costs quite expensive. The decoration of the walls, made using the panels discussed above, is much cheaper. However, all major techniques and subtleties remain almost the same as in the case of the use of chipboard-based panels and when finishing MDF panels.
Before putting the laminate, it is necessary to prepare tools for work, namely:
- spacer wedges;
- bobbish;
- rule;
- a hammer.
What do you need to know before starting work?
Before you decide to put a laminate, you need to know, to finish the walls in what premises it can be used. So, for example, it is impossible to put the laminate on the wall in the kitchen. Under the influence of temperature differences and high humidity, it will swallow and swallow. In the kitchen, such differences are not just very large, but also sharp and frequent. For the same reasons, it is impossible to lay the laminate on the wall in the basement and chulans.
Wall decoration with laminate can be performed in the corridor, living room and bedroom. In such premises, temperature and humidity parameters practically do not change.
Laminate scheme.
It is in the bedroom and a living room panel will be able to fully show their aesthetic qualities. It is impossible to lay the laminate on the wall and on the balcony, even if it is very well equipped.
Under the influence of high humidity, this material swells. It is necessary to take into account when finishing walls with laminate and leave indents (gaps) from the angles of 1.5-2 cm throughout the perimeter. If the installation is performed using spacer wedges, it will be done quite difficult, especially at the bottom of the walls. Therefore, you need to put on the bottom of the rail or flat board of a suitable thickness. If you decide to put a laminate on the wall with glue, this board must be wrapped with a thin plastic film. And already from the sides you can use wedges. And already in the end of the walls of the walls laminate, the gaps will need to close the plinth.
Article on the topic: Bordeur for paper wallpaper
In the event of wall decoration, laminate is recommended to install on the crate. However, if you have created any original design project, you can mount panels with glue.
Laminate laying guide on glue walls
Laminate laying scheme with adhesive way.
If, in the process of finishing the walls, the laminate will be attached using glue, then the most convenient to collect shields from individual panels, fitted in accordance with the designer idea, on the floor.
Take the glue and spread the side ends of the panels a sufficient thick layer, then glue them with each other. Before fixing the finished shields, make a markup on the wall. Lubricate the surface of the glue and attach the shields.
Laminate should begin to glue from the bottom left corner of the wall. Before starting work, remove door platbands. After finishing completion, return them to the previous place by setting over the facing. The technology of wall finishing laminate is quite simple. It allows you to quickly fill the entire surface. However, a much more reliable way is the installation of laminate for the crate.
Step-by-step instructions for installing laminate on the crate
Laminate mounting diagram with lock method.
Castle laminate is installed on the crate. If the surface of the wall is quite smooth, then liquid nails can be used. In this case, the installation of panels is carried out similarly to the above method of laying on glue. The difference is only that when creating shields, individual panels are connected through lock mounts, which are then treated with a sealant. In this case, the panels are attached to liquid nails.
Wooden rails and bars are suitable for making clamps, as well as wall guide metal profiles. In the case of a device for mounting panels, a special fastener is used, such as when working with MDF panels or eurry. Details of this fastener are known as a kleimer. In the event that the kleimer will prevent the edge of the subsequent laminate board in the groove previously laid, the lock can be cut. When laying a laminate on the walls, as in the case of the floor decoration, small gaps are left between the ceiling / floor and panels.
Article on the topic: Interior doors made of black glass in the interior
First of all, you need to measure and calculate the required number of panels and associated parts. Apply markup on the wall. Remove window and door platbands. Install the crate on the walls. The installation of panels should be started from the bottom left corner of the wall and move clockwise.
In the corners of the room of the panel, most likely, have to be short. This can be done with the help of electric jigsaw or woodcut. Planks are installed in a checker order. Before snapping the castle, the joints of the joints need to be treated with silicone. Continue work until the facing is fully completed. Corners are completed with aluminum profile and filled with silicone. Good job!