It happens that the door itself opens. What to do in such a situation? Spontaneous door opening is most often associated with poor installation of the door frame. This interroom door begins to strike the wall, it can touch the limiter. As a result, rapid wear occurs. This may be a sign of providing interior door, and such a lack can be corrected.
The main reason for the breakdown and skewers are broken or incorrectly installed loops.
First of all, the reason for the opening can be hinges. Poor installation hinges causes the battery, the door begins to open with difficulty.
One of the reasons may be the separation of one half of the loop. If the box is installed in terms of the level, the hinge marking was carried out, and the web still deviates from the vertical, which means that defective loops were installed. They need to be replaced.
Another reason may be poorly made grooves under the loop. For example, one edge has a recessed more than the other. This lack is easy to correct. It is necessary to remove everything more superfluous in the groove, put the material of the required thickness under the depression.
Another reason can be screws that were crookedly twisted in the loop. They pull the loop in the opposite direction. To fix the position, you need to replete holes.
What may be required for work
The loops are fastened with self-drawing in each hole.
- a hammer;
- Screwdriver figure;
- ax;
- scrap;
- electric drill;
- chisel;
- rasp;
- screws;
- a piece of chalk;
- level.
Door box and its effect on opening and closing interior door
Door box repair options.
If the door canvas opens involuntarily, the rack that holds the canvas does not have an ideal vertical. What is the reason how to fix such a problem? Loss of verticality due to improperly installed door loops - the main reason for self-opening. The loops are installed with a slight inclination.
If the opening occurs outside, it means that the tilt of the door is directed not to the door frame. To correct the position, you need to put the material of the corresponding thickness under the upper door loop.
Article on the topic: An apron for a kitchen from tile do it yourself
If an arbitrary closing occurs, the slope is directed towards the door frame. To eliminate the cause, you need to put the material under the door loop installed below.
After the rack is exhibited exactly vertically, the door will work perfectly. If still simple lining failed to correct the situation, you must re-install the door frame.
For this, all screws are removed, fastening the box. There is only one to hold the rack. The door canvas is removed. A well-sharpened knife removes all mounting foam. It is not necessary to remove the foam, it will be a kind of clinia substitute and will not allow the rack under the tilt to touch the wall.
Then, with the help of the level there is a new location of the rack. Through the rack, new holes are drilled. It will take a long drill to work. Dowels clogged into the holes.
Door box repair scheme.
After that, they hang the box and screw the electric drill two screws into the lower and top loop. This is necessary to verify the correct installation. If, when opening the door to 45 °, it does not save and remains on the spot, you can fully fix the box. If defects occur, it is necessary to check the vertical again. Such work is completed by removing the old foam, rack and re-gate.
It is always necessary to remember that other racks will have to be aligned in the same way. The amount of work related to the repair of the box depends on the degree of damage.
Perhaps it will be possible to do with simple cosmetic repairs. It will be quite enough to sharpen dents and paint the door. But it may be necessary to more serious repairs when it is necessary to replace the damaged details of the door frame and the door canvase.
When repairing metal doors, work is performed:
- plumbing;
- welding;
- finishing;
- Door gains.
Scripping the door is eliminated by lubricant loops.
Sometimes the door begins to creak. This is associated with friction in the canopy. It is possible to fix it with ordinary machine oil, lubricating the loop. You can use oil that lubricates sewing machines. To get to the loop axis, you need to put a wedge and pry, for example, scrap. It slightly raises, in the resulting clearance around the loop pins, oil is dripping. The door can be carefully lowering in its place. The main thing is that she remains all the time on the loop. The creak will disappear.
Article on the topic: How to choose a light-proof curtains Blackout in IKEA and Lerua Merlin
Instead of oil, you can use pieces of graphite, breaking any soft pencil.
Slices of graphite will be crushed by a mass of the door and become a small powder. Graphite is a magnificent lubricant, it will serve for a very long time.
If the metal door begins to open independently, it will have to fix the incorrect loops. The fastening of the loops must be done strictly vertically, no inclination is allowed.
How to repair loops
Poor-made grooves are aligned with the chisel.
If the opening occurs spontaneously, it means there is a tilt relative to the door frame. To correct the position, it is necessary to cut a little cardboard on top of the loop to install a loop in an even position. If an arbitrary closing occurs, then the cardboard must be placed under the loop from the bottom.
When working does not need to completely turn the screws. They can be unscrewed only half. In the resulting gap, you can put a piece of cardboard. After working, the screws are easily screwed back.
If the door is often clinically, in most cases it is associated with hinges that are very sore. To fix it is necessary to remove the screw, and instead you will screw the other, longer. Thus, changing all the screws, holding the loop, you can fix the situation.
If such an operation did not help, it is necessary to transfer the loops to a new place by moving them aside. You can try to make nest nests deeper than them to drown a little.
In some cases, the jamming of the door associated with the sedimentation building occurs. The door frame has undergone deformation and leaned slightly. The only output from the situation will be the creation of an angle of inclination corresponding to the corner of the frame.
Under the loop you need to put the gasket according to the technology described above. When encouraging half the door located downstairs, the laying is placed under the loop located at the top, and when it jars the upper half, everything is done on the contrary.
Rules for spinning samorezov
The cause of the encoding is the resulting great gap when installing the loop and the door frame. To eliminate the problem, the nest loops must be made much deeper and slightly drown them. If there is a skew, it is necessary to drown only that loop, which is the cause of the jam.
Article on the topic: Device Arches on the balcony
If the work done did not help eliminate the jam, you need to remove the wood layer opposite the junction site. The same is done with a door that swallowed from dampness. It is often quite enough to handle the end of the Raspil right on the hinges. To remove a thick layer, the door must be removed from the loops.
If when opening the door hits the floor
Perhaps this is due to the shrinkage of the door canvase. Correction of the position is similar to the operation of the door lubricant.
First, the steel door is pinned with a small wedge. In the open position, the canvas will start lifting in the loop. In the resulting gap are inserted semiring from durable wire. When the semiring is inserted, they need to hold them with the help of the passage until the ring is obtained. It must be done in such a way that the ring remains in place when the cloth will be closed or open.
When the door began to close badly, it is necessary to put copy paper under it, and then close. After opening, you can see the main cause of the problem. If the lock has a tongue below the hole below, it is necessary to check the strength of the fastening of loop screws. Perhaps the sediment occurred due to the fact that they were weakened.
If the actions did not led to success, it is necessary to remove the shut-off bar, and the holes to expand the ordinary file. After that, you can fix the bar elsewhere.
Displacement loops if the door sits tightly in place, not allowed. Sometimes you need to limit the door opening. For this, the strap is taken, which needs to be consolidated at the top of the door directly to the jam. The length of the strap is equal to the desired length of the opening. When the door is closed, the strap will just hang. To make the door itself, you can install the door closer.